New D4M (4/17/19) Initial Configuration and Setup

From Idrive
Revision as of 17:19, 23 April 2019 by Mark (talk | contribs) (Created page with "=Process steps for configuration of New Idrive D4 (4/17/19) for Customers. (Firmware Update, Idrive Default Configuration, Install Hard Drive)= ===Check Firmware version to v...")
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search

Process steps for configuration of New Idrive D4 (4/17/19) for Customers. (Firmware Update, Idrive Default Configuration, Install Hard Drive)

Check Firmware version to verify that this main board has the V206-2019/4/12-10:11:124 installed

This firmware begins with the New D4's arriving after 4/17/19.


  • The firmware version can be checked by accessing the D4 menu>system>system info with the remote or the USB Mouse inserted in the front panel's USB port. The Display can be viewed using Amcap on the PC and the output from the D4..

Note: The latest firmware can be downloaded from the downloads section of Admin Center

px 250

Enter the serial number and Board Version into Admin Center

  • Get the Serial Number from sticker on the back of the unit. (HDxxxxxxx type number)
  • Enter it into Admin Center. Also record in MENU>MOTOR>LICENSE ID
AC/Support/Devices/New D4-DVR Click on ADD and enter the S/N

Install Hard Drive into the Hard Drive carriage

  • step1

Install the Hard Drive into the Hard Drive Carriage.

  • Step 2
  • Do not reinstall the Hard Drive carriage into the D4-DVR until after configuration steps are completed

Setup the D4 for configuration

  • Plug in the Power Cable
  • Plug in the Monitor Cable
  • Plug in the Camera Cable
  • Turn power supply on
  • Insert the firmware and configuration SD Card into the unit
  • Turn the Key on ( wait ~40 Seconds for video and ~25 seconds for “Loading Disk”)
  • Press STOP on Remote Control to stop recording.


Confirm Application version is the latest

[See FirmWare upgrade above]

Using the Remote - MAINMENU>SYSTEM>SYSTEM UPGRADESee FirmWare upgrade above]]
  • Compare the installed version to the latest version. If different update it to the current release.
Update firmware MAINMENU>SYSTEM>SYSTEM UPGRADE - Update File
Note - This file is located on the SDcard that you have inserted in the D4

Install the Idrive standard configuration

  • Read the configuration file EZ config XML from the SD card MAINMENU>SYSTEM>CONFIG OPERATION>IMPORT CONFIGURATION> the UNIT will restart the App
Note - This file is located on the SD card that you have inserted in the D4, if the application freezes with blank green fields, turn the power key OFF and back ON
  • Press STOP on Remote Control to stop recording.
  • Confirm the config MAINMENU>SYSTEM>COMMON SETTINGS>TRANSPARENT = TRANSPARENT? If not the config did not get set.
  • Confirm the Alarm Configuration appears like the image below MAINMENU>SETTINGS>ALARM SETTINGS>

px250


  • Confirm the Alarm Wire A01 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

px250

  • Enter the serial number for the D4-DVR into the “LICENSE ID” MENU>MOTOR>LICENSE ID
  • Set the CUSTOMER's Time Zone MENU>SYSTEM.
  • Set the CUSTOMER's Time MENU>SYSTEM.
    • NOTE: time is in military format.
  • In MENU>PERIPHERALS, change the Baudrate to 9600… then Esc>Save
  • Turn Key OFF
  • Remove SD Card

Final configuration and Test

  • Install the hard drive carriage into the DVR
  • Turn the key ON
  • Format the hard drive MENU>STORAGE>FORMAT
  • Push record and verify that it can write to the hard drive.
  • Push stop
  • Test all camera ports with a working camera to ensure that they all work.
  • Turn the Key and Power supply off.
  • Box up unit with serial number on the outside of the box
Retrieved from "https://admincenter.idriveglobal.com/wiki/index.php?title=New_D4M_(4/17/19)_Initial_Configuration_and_Setup&oldid=9909"