Difference between revisions of "Manufacturing:X2 Camera Top Level Assembly"

From Idrive
Jump to navigation Jump to search
(Blanked the page)
 
Line 1: Line 1:
−
==Idrive X2 Camera Top Level Assembly==
 
  
−
===Driver Side Case Assembly===
 
−
This one?
 
−
{| class="wikitable"
 
−
|-
 
−
!'''X2 Drive Side Case Materials'''
 
−
|-
 
−
|Driver Side Plastic Case
 
−
|-
 
−
|LED Plastic Lens
 
−
|-
 
−
|X2 Main Board and LED Assembly
 
−
|-
 
−
|}
 
−
 
−
 
−
'''1.''' Snap the LED Lens into the Driver Side Case 
 
−
 
−
::- Ensure that the two LED indents are towards the bottom of the camera
 
−
 
−
::- Clear LED lens is shown to enhance the view of indents
 
−
 
−
::- Actual LED Lens is black/opaque as shown
 
−
 
−
 
−
[[File:x2_led_lens_assy.jpg|320px|]]
 
−
 
−
<br/><br/>
 
−
 
−
'''2.''' Snap the LED Board Assembly into the Driver Side Case as shown
 
−
 
−
[[File:x2_led_assy_incase.jpg|300px|]]
 
−
 
−
<br/><br/>
 
−
 
−
'''3.''' Snap the X2 Main board Assembly into the Driver Side Case as shown
 
−
 
−
[[File:x2_main_driver_case.jpg|250px|]]
 
−
 
−
 
−
<br/><br/>
 
−
 
−
===Road Side Case Assembly===
 
−
 
−
{| class="wikitable"
 
−
|-
 
−
!'''X2 Road Side Case Materials'''
 
−
|-
 
−
|Road Side Plastic case
 
−
|-
 
−
|Plastic Support Spur
 
−
|-
 
−
|Screw for Support Spur
 
−
|-
 
−
|FCC Compliance Label
 
−
|-
 
−
|}
 
−
{| class="wikitable floatcenter"
 
−
|-
 
−
!'''Electronic Module Materials'''
 
−
|-
 
−
|SparkLan WiFi Module
 
−
|-
 
−
|WiFi cable
 
−
|-
 
−
|Dual Band WiFi Antenna
 
−
|-
 
−
|Screws for WiFi mounting
 
−
|-
 
−
|GPS Module Assembly
 
−
|-
 
−
|}
 
−
 
−
 
−
'''1.''' Attach Base Support Spur to the Road Side Case with the screw (Note correct orientation of Support Spur)Place FCC compliance sticker as shown.
 
−
 
−
[[File:x2supportspur2.jpg|300px|]][[File:x2_fcc_compliance_sticker.jpg|300px|]]
 
−
 
−
 
−
'''2.''' Install the Wifi Module with cable and antenna, secure with 2 screws as shown
 
−
 
−
[[File:x2wifimodule1.jpg|300px|]][[File:x2wifimodule2.jpg|250px|]]
 
−
 
−
 
−
'''3.''' Install GPS Module as shown. Ensure the cable is routed properly so as to avoid he power connector opening.
 
−
 
−
[[File:x2gpsmodule1.jpg|320px|]][[File:x2gpsmodule2.jpg|320px|]]
 
−
 
−
 
−
<br/><br/>
 
−
 
−
 
−
 
−
===Top Level Camera Assembly===
 
−
 
−
{| class="wikitable"
 
−
|-
 
−
!'''X2 Top Level Camera Materials'''
 
−
|-
 
−
|Driver Side Case Assembly
 
−
|-
 
−
|Road Side Case Assembly
 
−
|-
 
−
|Bar Code Label with Serial Number
 
−
|-
 
−
|Plastic Dust Cover for Accessory Connectors
 
−
|-
 
−
|Case Screw
 
−
|-
 
−
|Wifi Antenna
 
−
|-
 
−
|}
 
−
 
−
'''1.''' Connect the GPS and WiFi Cables to the Main Board. Remove the backing tape from the wifi antenna and affix the Antenna on the Driver Side Case as shown.
 
−
 
−
[[File:X2wifiantenna.jpg|320px|]]
 
−
 
−
 
−
'''2.''' Snap the two halves of the camera together ensuring no cables interfere with or block the Lens, Power Connector, I/O Connectors, USB opening or case screw
 
−
 
−
[[File:x2wifiandgpsattachment.jpg|320px|]][[File:x2twohalves.jpg|320px|]]
 
−
 
−
'''3.''' Install Plastic Dust Cover for Accessory Connectors - move to after final test.
 
−
 
−
[[File:x2accessorycover.jpg|320px|]]
 
−
 
−
 
−
'''4.''' Secure the cases to together with the case screw. Do not over torque the screw.
 
−
 
−
[[File:x2casescrew1.jpg|320px|]]
 
−
 
−
<br/><br/>
 
−
 
−
===Windshield Support Assembly===
 
−
 
−
{| class="wikitable"
 
−
|-
 
−
!'''X2 Windshield Support Materials'''
 
−
|-
 
−
|Plastic Windshield Support
 
−
|-
 
−
|Plastic Support Back Plate
 
−
|-
 
−
|Screw for Support Back Plate
 
−
|-
 
−
|3M Adhesive Tape
 
−
|-
 
−
|Screw for Support attachment to Spur
 
−
|-
 
−
|Washer for Support Screw
 
−
|-
 
−
|Locknut for Support Attachment
 
−
|-
 
−
|}
 
−
 
−
'''1.''' Assemble Windshield Support Base Assembly (Windshield support not attached to the camera until after final test or else the power connector would be inaccessible
 
−
 
−
::* Snap plastic back plate into support
 
−
 
−
::* secure with screw
 
−
 
−
::* Apply 3M tape and trim flush with scaple
 
−
 
−
 
−
[[File:x2winshieldsupport2.jpg|300px|]][[File:x2winshieldsupport.jpg|320px|]] [[File:x2winshieldsupporttape.jpg|350px|]]
 
−
 
−
 
−
<br/><br/>
 

Latest revision as of 19:31, 17 July 2015

Retrieved from "https://admincenter.idriveglobal.com/wiki/index.php?title=Manufacturing:X2_Camera_Top_Level_Assembly&oldid=5577"