Revision as of 17:01, 15 March 2017

D8 Configuration and Setup

Assemble System

Place default configuration (Parameters file on the SSD

Install SSD

put Batteries in the remote (batteries not included w/D8)

Plug in the D8 Power cable (NOT a D4 Cable!)

Plug in the 16 wire Harness and attach the StarTech USB device

Install the SIM card (what SIM, how to document etc)

Configuration "Parameters" Discussion

From Al 3/14

1. This will set ever D8 the same and there needs to be changes to each config for Terminal (which is the last 6 digits of the serial number)

3. Also I just got to setting the Alerts and only have one camera set to “EXIGENCY” – which means when disconnected send an ALARM, but I just found out I cannot duplicate the ALARM in the same window for more cameras ALARM… we get a weird alarm text when trying to save… chinglish

To make the param.xml file for Mark, I had to change the device 6 digit number ID number. I used the last six digits of the serial number from the label on the side…

Since then I changed the unit number in the software and have not been able to connect again… I made no change to the APN data that is the same…

The DVR shows the icon as connected to the server, but I cannot get the data or tracking on the server… am working with Chinese right now…

From Al 3/15

It was unexplained. But the vehicle name must be the same as the Phone number field.

Parameters file differences

Comparison of Al's initial config and the default config

<KeyPara

MD5 different

<BaseSetup

TimeZone (Al = 7 Default = 20)

timingtime (Al = "00:00:00" Default = "06:30:00")

OprTimeOut (Al = 120 Default = 30)

<TerminalSetup

device_num (Al = 225001 Default = 10000)

Phonenumber (Al = Blank Default = 1000)

company_name (Al = "idr" Default = Blank)

Authentication (Al = "225001" Default = 10000)

<RecordSet

CameraType (Al = "0" Default = 1)

<RecordSetMainChNoSet

Resolution (Al = "2" Default = 0)

<RecordSetMirrorChNoSet

isRec (Al = "1" Default = 0)

<SystemPowerSet

PowerOnTime (Al = "00:00:00" Default = 06:00:00)

PowerOffTime (Al = "00:00:00" Default = 22:00:00)

<MonitorSet

showNum (Al = 9 Default = 8)

<NetWorkSet

IpAddr (Al = 10.7.7.14 Default = 192.168.1.80)

GateWay (Al = 10.7.7.1 Default 192.168.2)

DNS1 (Al = 65.32.5.111 Default 192.168.1.2)

DNS2 (Al = 65.32.5.111 Default 192.168.1.2)

AL:

Default:

<CenterNetwork __id="7" Enable="1" Type="0" CenterIP="113.108.120.47" ContrlPort="21" DomainName="" /

<DialUpSet

APN (Al = data641003 Default = 3gnet)

UserName (Al = Blank Default = card)

UserPwd (Al = Blank Default = card)

SimICCID (Al & Default = "89860115851042424258") Why are these the same?

SmsCenter (Al = Blank Default = +8613010888500)

<WifiSet

Encrypt (Al = 2 Default = 3)

SSID (Al = Blank Default = 888

Pwd (Al = Blank Default = 88888888)

IpAddr (Al = 255.255.255.255 Default = 192.168.2.10)

SubNet (Al = 255.255.255.255 Default = 255.255.255.0)

GateWay (Al = 255.255.255.255 Default = 192.168.2.1)

Purpose (Al = 16 Default =0)

<AlarmSet

Al:

   <SensorAlarmSet __id="0" Name="Exigency" Enable="1" isRecord="1" LimitValue="1" HoldTime="3" DelayTime="1" linkage="32" HomePageChannel="0" />
   <SensorAlarmSet __id="1" Name="OFF" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="2" Name="OFF" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="3" Name="OFF" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="4" Name="OFF" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="5" Name="OFF" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="6" Name="OFF" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="0" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="7" Name="OFF" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="8" Name="IO9" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="9" Name="IO10" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="10" Name="IO11" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="11" Name="IO12" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="12" Name="IO13" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="13" Name="IO14" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="14" Name="IO15" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="15" Name="IO16" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />

Default:

   <SensorAlarmSet __id="0" Name="IO1" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="1" Name="IO2" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="2" Name="IO3" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="3" Name="IO4" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="4" Name="IO5" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="5" Name="IO6" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="6" Name="IO7" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="7" Name="IO8" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="8" Name="IO9" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="9" Name="IO10" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="10" Name="IO11" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="11" Name="IO12" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="12" Name="IO13" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="13" Name="IO14" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="14" Name="IO15" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />
   <SensorAlarmSet __id="15" Name="IO16" Enable="0" isRecord="0" LimitValue="1" HoldTime="3" DelayTime="1" linkage="0" HomePageChannel="0" />

<SubStreamSet

bitRate (Al = "400" Default = 160)

targetFrame (Al = ="25" Default = 4)

<UserParam

AL:

intParam0="255" intParam1="255" intParam2="255" intParam3="255" intParam4="255" intParam5="255" intParam6="255" intParam7="255" doubleParam="0.000000" charParam=""

Default:

intParam0="0" intParam1="0" intParam2="0" intParam3="0" intParam4="0" intParam5="0" intParam6="0" intParam7="0" doubleParam="0.000000" charParam=""

Things we may need/want to set

<SystemInfo Product_List_info , Manufacturer

<SecuritySet

AdminPassword (Default 666666)

UserPassword (Default 000000)

<Front0sdSet

<ChlName __id="0" ChlName="CH1" (Change "CH1" to "Crane front Left" etc?)

Camera Connections

On the Back Panel

AV IN #1 connector - White - CH1 Yellow = CH2

AV IN #2 connector - White - CH3 Yellow = CH4

AV IN #3 connector - White - CH5 Yellow = CH6

AV IN #4 connector - White - CH7 Yellow = CH8

@@ Line 17: / Line 17: @@
 <br><br>
-==Import Configuration "Parameters" File==
+==Configuration "Parameters" Discussion==
-Press "login" button on the remote
+'''From Al 3/14'''
-enter password 666666 (admin)
+.	This will set ever D8 the same and there needs to be changes to each config for Terminal (which is the last 6 digits of the serial number)
+.	Also I just got to setting the Alerts and only have one camera set to “EXIGENCY” – which means when disconnected send an ALARM, but I just found out I cannot duplicate the ALARM in the same window for more cameras ALARM…  we get a weird alarm text when trying to save… chinglish
+To make the param.xml file for Mark, I had to change the device 6 digit number ID number. I used the last six digits of the serial number from the label on the side…
+Since then I changed the unit number in the software and have not been able to connect again… I made no change to the APN data that is the same…
+The DVR shows the icon as connected to the server, but I cannot get the data or tracking on the server… am working with Chinese right now…
+'''From Al 3/15'''
+It was unexplained. But the vehicle name must be the same as the
+Phone number field.
-navigate using left, right, up, down buttons to "Tools > Parameters"
-Click "Import Parameters" (Yes)
-D8 reboots with new parameters
 <br><br>

Difference between revisions of "D8 Initial Configuration and Setup"

Revision as of 17:01, 15 March 2017

Contents

D8 Configuration and Setup

Assemble System

Configuration "Parameters" Discussion

Parameters file differences

Things we may need/want to set

Camera Connections

Navigation menu

Search