Difference between revisions of "Netwatch Script Reboots MikroTik"
| (5 intermediate revisions by the same user not shown) | |||
| Line 11: | Line 11: | ||
'''To set it up - follow these steps using Winbox:''' | '''To set it up - follow these steps using Winbox:''' | ||
| − | + | '''1.''' Go to System>Scripts | |
Click on the red "+" | Click on the red "+" | ||
Give your script a Name (in my example I will use "NetWatchBoot-192.168.0.10" | Give your script a Name (in my example I will use "NetWatchBoot-192.168.0.10" | ||
| − | + | '''2.''' In the Source: area paste in the entire line below: '''WITHOUT THE QUOTES " "''' | |
| − | :if ([/ping 192.168.0.10 interval=5 count=60] =0) do={ | + | |
| + | |||
| + | ":if ([/ping 192.168.0.10 interval=5 count=60] =0) do={ | ||
log info "my ping watchdog is down" ; /system reboot | log info "my ping watchdog is down" ; /system reboot | ||
| − | } | + | }" |
| − | + | ||
| + | '''3.''' Click the Apply button - then click the OK button | ||
| Line 29: | Line 32: | ||
'''At this time - we have a script - it is not running or active yet.''' | '''At this time - we have a script - it is not running or active yet.''' | ||
| − | + | '''1.''' Go to Tools>Netwatch | |
Click on the red "+" | Click on the red "+" | ||
On the Host tab - type in 192.168.0.10 | On the Host tab - type in 192.168.0.10 | ||
| Line 35: | Line 38: | ||
Set interval for 00:01:00 min | Set interval for 00:01:00 min | ||
| − | + | '''2.''' Click on the Down tab | |
| − | Paste in the line below: | + | Paste in the line below: '''WITHOUT THE QUOTES " "''' |
| − | /system script run NetWatchBoot-192.168.0.10 | + | |
| + | |||
| + | "/system script run NetWatchBoot-192.168.0.10" | ||
| − | |||
| + | '''3.''' Click the Apply button - then click the OK button | ||
'''Reboot the Router from System>Reboot>Yes''' | '''Reboot the Router from System>Reboot>Yes''' | ||
Latest revision as of 17:16, 6 February 2017
Mikrotik Netwatch script on AP for auto reboot ...
http://forum.mikrotik.com/viewtopic.php?t=56138
First - what this does:
- It will ping test an IP address. This is a remote IP address (such as the Base Station IP 192.168.0.10)
- If the remote IP address does not answer any pings for 5 minutes, then the router reboots.
To set it up - follow these steps using Winbox:
1. Go to System>Scripts Click on the red "+" Give your script a Name (in my example I will use "NetWatchBoot-192.168.0.10"
2. In the Source: area paste in the entire line below: WITHOUT THE QUOTES " "
":if ([/ping 192.168.0.10 interval=5 count=60] =0) do={
log info "my ping watchdog is down" ; /system reboot
}"
3. Click the Apply button - then click the OK button
Here is the Logic... The above sample will ping 192.168.0.10 for 5 intervals of 60 seconds = 5 minutes
If it does not reach the the assigned script NetWatchboot IP address, the MikroTik will reboot
At this time - we have a script - it is not running or active yet.
1. Go to Tools>Netwatch Click on the red "+" On the Host tab - type in 192.168.0.10
Set interval for 00:01:00 min
2. Click on the Down tab Paste in the line below: WITHOUT THE QUOTES " "
"/system script run NetWatchBoot-192.168.0.10"
3. Click the Apply button - then click the OK button
Reboot the Router from System>Reboot>Yes