Difference between revisions of "Idrive Installer Processes and Guidelines"

From Idrive
Jump to navigation Jump to search
 
(15 intermediate revisions by the same user not shown)
Line 90: Line 90:
 
==D4 Installation==
 
==D4 Installation==
 
<br\><br\>
 
<br\><br\>
−
1) Confirm with customer as to the location of the D4 and cameras.
+
1) Confirm as to the location of the D4 and cameras.
  
 
2) Make sure that the mounting locations will not interfere with safe operation of the vehicle.
 
2) Make sure that the mounting locations will not interfere with safe operation of the vehicle.
  
−
3) Locate a good source for the power supplies Constant12v, Keyed12v & Ground.
+
3) Locate a good source for the power supplies Constant 12V, Keyed 12V & Ground.
  
 
4) Mount the D4 while making sure to leave room for all connections and the removal of the hard drive.
 
4) Mount the D4 while making sure to leave room for all connections and the removal of the hard drive.
  
−
5) The D4 is shipped with a power connector which has three wires '''red''' wire constant 12V, '''yellow''' wire switched 12v and '''black''' ground.
+
5) The D4 is shipped with a power connector which has three wires '''red''' wire constant 12V, '''yellow''' wire switched 12V and '''black''' ground.
  
 
6) Use a volt meter to check for constant 12V and switched 12V.
 
6) Use a volt meter to check for constant 12V and switched 12V.
  
−
7) Also supply will be a in-line fuse that will be connected to constant 12V red wire.
+
7) All so supply will be a in-line fuse that will be connected to constant 12V red wire.
  
−
8) You will need to connect the fuse using a butt connector not supplies.
+
9) Once all connections to the D4 have been made you will need to a line the cameras.
  
−
9) Once all connections to the D4 have been made you will need to a line the cameras.  
+
9) In order to do this you will need a monitor connected to the output on the D4.
  
−
10) Thin check that all idrive settings including the date, time and Time zone are set correctly.
+
10) Using the monitor check that the image from the cameras is level and that you are getting full coverage.
  
−
11) In order to do this you will need a monitor of some sort connected to the output of the D4.  
+
11) Check that the date and time are set correctly.
  
−
12) This can be done one of two ways if the customer ordered the monitor with their system you can use it.
+
12) Push record on the remote and verify that it can write to the hard drive.
−
Because the remote control must be pointed at the sensor on the front of the D4 this my present a problem.
 
  
−
13) Connecting the D4 to a laptop is the preferred method.
 
  
−
14) Once the laptop is connected to the D4 Will need to open Amcap software to view D4 outputs.
 
  
−
15) If you do not have Amcap loaded on your computer you can download it from the I drive Center under downloads.
 
  
−
16) You Will need to make sure that the key in the D4 is turned the on position and that the ignition for the vehicle is also in the on position.
 
  
−
17) Once you have seen the Idrive splash come up on the screen you can use the remote control to check and change any settings.
 
  
  
 
<br\><br\>
 
<br\><br\>

Latest revision as of 16:13, 17 October 2013

Idrive Installer Process and Guide

Base Station Installation

<br\><br\>

Quoting

Determine if customer is interested in Base Station and WiFI installation

Obtain Location of installation

  • To obtain an overhead view of the location to help evaluate WiFi placement and other issues

Obtain Contact(s) for:

  • IT (to help determine internet, existing equipment etc)
  • Facilities (structure type, electrical availability etc)
  • Fleet manager for location ( to discuss fleet patterns, areas to be covered etc)

Support looks over the location, discusses with customer personnel and develops a plan

Document it and cost it and get it to sales

Sales quotes the installation and any additional equipment required. Supplies map od site from support to pin down the scope of work


<br\><br\>

Upon Receipt of Order

Order equipment if not in stock

  • D4 DVRs
  • Correct mix of Cameras
  • Monitor?
  • Cables - how many, what length
  • Security Lock Box?
  • Disk Reader?


Schedule Installer based on equipment availability and customer schedule

<br\><br\>

Installer Initial Actions

Quantify the Job

  • How Many
  • Special tools or installation requirements
  • How Long should it take
  • Special instructions?

Scheduling

<br\><br\>

Installer costs

  • Travel?
  • cost per unit(s)


<br\><br\>

Sign off

<br\><br\>

X1 Installation

<br\><br\>


D4 Installation

<br\><br\> 1) Confirm as to the location of the D4 and cameras.

2) Make sure that the mounting locations will not interfere with safe operation of the vehicle.

3) Locate a good source for the power supplies Constant 12V, Keyed 12V & Ground.

4) Mount the D4 while making sure to leave room for all connections and the removal of the hard drive.

5) The D4 is shipped with a power connector which has three wires red wire constant 12V, yellow wire switched 12V and black ground.

6) Use a volt meter to check for constant 12V and switched 12V.

7) All so supply will be a in-line fuse that will be connected to constant 12V red wire.

9) Once all connections to the D4 have been made you will need to a line the cameras.

9) In order to do this you will need a monitor connected to the output on the D4.

10) Using the monitor check that the image from the cameras is level and that you are getting full coverage.

11) Check that the date and time are set correctly.

12) Push record on the remote and verify that it can write to the hard drive.




<br\><br\>

Retrieved from "https://admincenter.idriveglobal.com/wiki/index.php?title=Idrive_Installer_Processes_and_Guidelines&oldid=2767"