Difference between revisions of "Idrive Installer Processes and Guidelines"
| Line 108: | Line 108: | ||
9) Once all connections to the D4 have been made you will need to a line the cameras. | 9) Once all connections to the D4 have been made you will need to a line the cameras. | ||
| − | 10) In order to do this you will need a monitor | + | 10) In order to do this you will need a monitor connected to the output of the D4. |
| − | 11) Using the monitor check that the image from the cameras is level and that you are getting full coverage. | + | 11) Using the monitor check that the image from the cameras is level and that you are getting full coverage. |
| − | + | 00) Check that the date and time are set correctly. | |
| − | 13) | + | 13) Using the remote control. |
00) The remote control most be pointed at the front of the D4. | 00) The remote control most be pointed at the front of the D4. | ||
| + | |||
| + | 12) Check that all idrive settings including the date time and Time zone are set correctly. | ||
| + | |||
| + | |||
| + | |||
| + | |||
<br\><br\> | <br\><br\> | ||
Revision as of 15:33, 17 October 2013
Idrive Installer Process and Guide
Base Station Installation
<br\><br\>
Quoting
Determine if customer is interested in Base Station and WiFI installation
Obtain Location of installation
- To obtain an overhead view of the location to help evaluate WiFi placement and other issues
Obtain Contact(s) for:
- IT (to help determine internet, existing equipment etc)
- Facilities (structure type, electrical availability etc)
- Fleet manager for location ( to discuss fleet patterns, areas to be covered etc)
Support looks over the location, discusses with customer personnel and develops a plan
Document it and cost it and get it to sales
Sales quotes the installation and any additional equipment required. Supplies map od site from support to pin down the scope of work
<br\><br\>
Upon Receipt of Order
Order equipment if not in stock
- D4 DVRs
- Correct mix of Cameras
- Monitor?
- Cables - how many, what length
- Security Lock Box?
- Disk Reader?
Schedule Installer based on equipment availability and customer schedule
<br\><br\>
Installer Initial Actions
Quantify the Job
- How Many
- Special tools or installation requirements
- How Long should it take
- Special instructions?
Scheduling
<br\><br\>
Installer costs
- Travel?
- cost per unit(s)
<br\><br\>
Sign off
<br\><br\>
X1 Installation
<br\><br\>
D4 Installation
<br\><br\> 1) Confirm with customer as to the location of the D4 and cameras.
2) Make sure that the mounting locations will not interfere with safe operation of the vehicle.
3) Locate a good source for the power supplies Constant 12V, Keyed 12V & Ground.
4) Mount the D4 while making sure to leave room for all connections and the removal of the hard drive.
5) The D4 is shipped with a power connector which has three wires red wire constant 12V, yellow wire switched 12V and black ground.
6) Use a volt meter to check for constant 12V and switched 12V.
7) Al so supply will be a in-line fuse that will be connected to constant 12V red wire.
8) You will need to connect the fuse using a butt connector not supplies.
9) Once all connections to the D4 have been made you will need to a line the cameras.
10) In order to do this you will need a monitor connected to the output of the D4.
11) Using the monitor check that the image from the cameras is level and that you are getting full coverage.
00) Check that the date and time are set correctly.
13) Using the remote control.
00) The remote control most be pointed at the front of the D4.
12) Check that all idrive settings including the date time and Time zone are set correctly.
<br\><br\>