Transfer Point Documentation - Revision history

Abilotti: /* Connecting Remote WiFi Antennas */

2013-12-27T22:39:46Z

Connecting Remote WiFi Antennas

2013-12-27T22:38:26Z

Connecting Internet

2013-12-27T22:37:38Z

Connecting Internet

2013-12-27T22:32:24Z

Connecting 120V Power

2013-12-27T22:31:28Z

Mounting

2013-11-14T18:28:56Z

2013-09-18T23:01:15Z

Connecting 120V Power

2013-09-18T23:00:55Z

Connecting 120V Power

2013-09-18T22:57:36Z

2013-09-18T22:55:03Z

@@ Line 85: / Line 85: @@
 ===Connecting Remote WiFi Antennas===
-<span style="color: red"> ('''Note: If you are not familiar with the installing ether net cable. That you hire a professional installer.''')
+<span style="color: red"> ('''Note: If you are not familiar with the installing ethernet cable. Then we suggest that you hire a professional installer.''')
-)Bring the shielded ether net cable from remote WiFi antennas in to the terminal point. This needs to be don before installing supplied RJ-45 connector.
+)Bring the shielded ethernet cable from remote WiFi antennas in to the terminal point. This needs to be done before installing supplied RJ-45 connector.
-)Trad shielded ether net cable from remote WiFi antennas. Through one of the through wall fittings bottom right side of the terminal point.
+)Thread shielded ethernet cable from remote WiFi antennas. Through one of the through wall fittings on the bottom right side of the terminal point.
-)Connect supplied RJ-45 connector to shielded ether net cable.
+)Connect supplied RJ-45 connectors to shielded ethernet cable.
-)Then plug it into one of the Poe slot marked antennas.
+)Then plug it into one of the PoE slots marked antennas.

← Older revision		Revision as of 22:38, 27 December 2013
Line 70:		Line 70:
	===Connecting Internet===		===Connecting Internet===

−	<span style="color: red">('''Note: If you are not familiar with the installing ethernet cable. ~~That~~ you hire a professional installer.''')	+	<span style="color: red">('''Note: If you are not familiar with the installing ethernet cable. We suggest that you hire a professional installer.''')

@@ Line 70: / Line 70: @@
 ===Connecting Internet===
-<span style="color: red">('''Note: If you are not familiar with the installing ether net cable. That you hire a professional installer.''')
+<span style="color: red">('''Note: If you are not familiar with the installing ethernet cable. That you hire a professional installer.''')
-)Bring the ether net cable in to the terminal point needs to be don before installing supplied RJ-45 connector.
+)Bring the ethernet cable in to the terminal point which needs to be done before installing supplied RJ-45 connector.
-)Trad ether net cable through one of the through wall fittings bottom right side of the terminal point.
+)Thread ethernet cable through one of the through wall fittings on the bottom right side of the terminal point.
-)Connect supplied RJ-45 connector to ether net cable. Then plug it into the PoE slot marked Internet.
+)Connect supplied RJ-45 connector to ethernet cable. Then plug it into the PoE slot marked Internet.

@@ Line 49: / Line 49: @@
 [[File:tp2.jpg|thumb|400px|]]
 [[File:bottomTP.jpg|thumb|375px|]]
-)Once the Terminal Point is mounted you'll need to run power to ti.<span style="color: red"> (Mount it how?)
+)Once the Terminal Point is mounted you'll need to run power to it.<span style="color: red"> (Mount it how?)
 )There is a Flexible Conduit Fitting in the bottom center of the Terminal Point for.

@@ Line 35: / Line 35: @@
 )Measure from the ground to find desired height.
-)Using level and tape measure to mark the location of mounting hols or installation point of other hardware.
+)Using level and tape measure to mark the location of mounting holes or installation point of other hardware.
 )Mounting the Terminal Point so that it is level is important.

← Older revision		Revision as of 18:28, 14 November 2013
Line 1:		Line 1:
−	=Idrive Transfer Point Documentation=	+	=Idrive Remote Transfer Point Documentation=

	<br\><br\>		<br\><br\>

@@ Line 48: / Line 48: @@
 [[File:tp2.jpg|thumb|400px|]]
-[[File:bottomTP.jpg|thumb|400px|]]
+[[File:bottomTP.jpg|thumb|350px|]]
 )Once the Terminal Point is mounted you'll need to run power to ti.<span style="color: red"> (Mount it how?)

← Older revision		Revision as of 22:55, 18 September 2013
Line 47:		Line 47:


		+	[[File:tp2.jpg\|thumb\|400px\|]]
	[[File:tp2.jpg\|thumb\|400px\|]]		[[File:tp2.jpg\|thumb\|400px\|]]
	1)Once the Terminal Point is mounted you'll need to run power to ti.<span style="color: red"> (Mount it how?)		1)Once the Terminal Point is mounted you'll need to run power to ti.<span style="color: red"> (Mount it how?)