Manufacturing:X2 Main Board Initial Programming and Test - Revision history

Mark at 22:28, 28 July 2015

2015-07-28T22:28:32Z

Mark at 21:06, 20 July 2015

2015-07-20T21:06:29Z

Mark: /* X2 Automatic Install and Configuration */

2015-07-17T19:57:37Z

X2 Automatic Install and Configuration

Mark: Created page with "==Idrive X2 Main Board Initial Programming== {| class="wikitable" |- !'''Idrive X2 Programming & Lens Focus Materials''' |- |Idrive X2 Programming Station |- |Idrive Top Leve..."

2015-07-17T18:58:35Z

Created page with "==Idrive X2 Main Board Initial Programming== {| class="wikitable" |- !'''Idrive X2 Programming & Lens Focus Materials''' |- |Idrive X2 Programming Station |- |Idrive Top Leve..."

New page

==Idrive X2 Main Board Initial Programming==

{| class="wikitable"
|-
!'''Idrive X2 Programming & Lens Focus Materials'''
|-
|Idrive X2 Programming Station
|-
|Idrive Top Level X2 Main Board Assembly
|-
|Lens focus targets
|-
|Super Glue (for fixing lenses) (Loctite Control, Extra Time or equivalent)
|-
|}

 

====Initialize Firmware Programming Station====

[[#Appendix B - Idrive X2 Programming Station Documentation | X2 Programming Station Setup]]

[[File:idr_x2_pgmr_sta1.jpg|400px|]]

====Setup X2 Main Board====

'''1.''' Place the Idrive X2 Main board into the Device holding Fixture.

'''2.''' Connect the Power cable between the Idrive X2 Main Board and the Programming Fixture.

'''3.''' Connect the serial programming cable between the Idrive X2 Main Board and the Programming Fixture. (observe polarity)

'''4.''' Connect the USB Network Adapter to the Idrive X2 Main Board.

[[File:idr_x2_pgmr_front.jpg|340px|]] [[File:idr_x2_pgmr_back.jpg|340px|]]

<br\><br\><br\><br\>

====X2 Automatic Install and Configuration====

Notes: The Automatic install performs the following:

::* installes the boot loader into the X2 board. (The Kenel and filesystem are pre-installed with the 8GB SD card)

::* gets device configuration from the Idrive AdminCenter (IP address configuration)

::* Tests triggering on the yellow, blue and green wires

::* provides lens focus mode so both lenses can be focused and glued

'''1.''' Click on the Factory-New Devices-Auto button [[File:ft_factoryauto_button.jpg|250px|]]

 

'''2.''' Scan the Bar Code label on the device to be programmed and press Enter.

(if no bar code scanner is available type the serial number from the bar code label into the serial number input field )

[[File:x2_scan_serial_auto.jpg|250px|]]

 

'''3.''' Click on the Auto Install Button and the Automatic Install window will open, Click on Start Installation

[[File:x2_auto_pgmr_phase1.jpg|650px|]]

: If any of these steps fail the program will stop and give an error. Common errors are:

::* Missing or corrupt OS on 4GB SD card

::* Missing or corrupt storage SD card

::* Serial cable not connected

::* USB NIC or Internet connection missing

::* I/O ports tester board missing

::* Any assembly or incorrect component error

If all steps are successfully completed the program will enter into Lens Focus / LED test mode Mode.

 

====Lens Focusing====

[[File:x2_focusmode_both_sides.jpg|600px|]]

'''1.''' Select "Inside Camera" Tab and Focus the Driver Side Lens(DSL-180A) (the same side as the Processor). '''The focal length for the inside camera should be ~1.5 meters'''

[[File:x2_focusmode_outside_no_zoom.jpg|600px|]]

'''2.''' Select "Outside camera" Tab and Focus the Road Side Lens (DSL-218A) (the same side as Power Connector). '''The Focal Length for the outside camera should be 6 meters''' Use zoom mode to ensure accurate focus.

[[File:x2_focusmode_outside_zoom.jpg|600px|]]

'''3.''' Select "Both cameras" Tab and Verify the lenses are focused.

'''4''' Verify that the 4 IR LEDs are on (faint red glow in 4 places)

[[File:x2_irled_check.jpg|300px|]]

'''5.''' If images are focused and clear and the 4 IRLeds are on click on the "Lens Focus OK" button and the focus mode will close. If the image is not clear or any IRLeds are not functioning for some reason click on the "Lens Focus Not OK" the factory tool will exit focus mode so corrective action can be taken.

'''6.''' Remove the assembly from the test fixture

'''7.''' Once focused fix the each lens with a drop of super glue.'''Test the lenses after several minutes to ensure they have taken the glue and cannot be moved'''

'''8.''' Advance the Main Board Assembly to the Driver Side Case Assembly Station.

@@ Line 97: / Line 97: @@
 ====Lens Focusing====
 '''1.''' Select "Inside Camera" Tab and Focus the Driver Side Lens(DSL-180A) (the same side as the Processor).
@@ Line 109: / Line 105: @@
 '''2.''' Select "Outside camera" Tab and Focus the Road Side Lens (DSL-218A) (the same side as Power Connector).
-::*'''The Focal Length for the outside camera should be 6 meters'''
+::*'''Focus using the provided Idrive Focus Chart. Distance to chart can be 3,6,9 feet but the farther the better. '''
 ::*Use zoom mode to ensure accurate focus
-[[File:x2_focusmode_outside_no_zoom.jpg|600px|]]
+[[File:x2_lens_focus.jpg|600px|]]
 '''4''' Verify that the 4 IR LEDs are on (faint red glow in 4 places)

← Older revision		Revision as of 19:57, 17 July 2015
Line 86:		Line 86:

	If all steps are successfully completed the program will enter into Lens Focus / LED test mode Mode.		If all steps are successfully completed the program will enter into Lens Focus / LED test mode Mode.
−
−

	<br/><br/>		<br/><br/>

@@ Line 6: / Line 6: @@
 |-
 |Idrive X2 Programming Station
 |-
 |Idrive Top Level X2 Main Board Assembly
@@ Line 15: / Line 17: @@
 |}
-<br/><br/>
+<br/>
 ====Initialize Firmware Programming Station====
@@ Line 36: / Line 38: @@
 '''4.''' Connect the USB Network Adapter to the Idrive X2 Main Board.
 [[File:idr_x2_pgmr_front.jpg|340px|]] [[File:idr_x2_pgmr_back.jpg|340px|]]
-<br\><br\><br\><br\>
+<br\><br\>
 ====X2 Automatic Install and Configuration====
@@ Line 45: / Line 52: @@
 Notes: The Automatic install performs the following:
-::* installes the boot loader into the X2 board. (The Kenel and filesystem are pre-installed with the 8GB SD card)
+::* installs the boot loader into the X2 board. (The Kernel and filesystem are pre-installed on the 4GB SD card)
 ::* gets device configuration from the Idrive AdminCenter (IP address configuration)
@@ Line 95: / Line 102: @@
-'''1.''' Select "Inside Camera" Tab and Focus the Driver Side Lens(DSL-180A) (the same side as the Processor). '''The focal length for the inside camera should be ~1.5 meters'''
+'''1.''' Select "Inside Camera" Tab and Focus the Driver Side Lens(DSL-180A) (the same side as the Processor).
-'''2.''' Select "Outside camera" Tab and Focus the Road Side Lens (DSL-218A) (the same side as Power Connector). '''The Focal Length for the outside camera should be 6 meters''' Use zoom mode to ensure accurate focus.
+'''2.''' Select "Outside camera" Tab and Focus the Road Side Lens (DSL-218A) (the same side as Power Connector).
-[[File:x2_focusmode_outside_zoom.jpg|600px|]]
+::*Use zoom mode to ensure accurate focus
 '''3.''' Select "Both cameras" Tab and Verify the lenses are focused.
@@ Line 112: / Line 123: @@
 '''5.''' If images are focused and clear and the 4 IRLeds are on click on the "Lens Focus OK" button and the focus mode will close. If the image is not clear or any IRLeds are not functioning for some reason click on the "Lens Focus Not OK" the factory tool will exit focus mode so corrective action can be taken.
-'''6.''' Remove the assembly from the test fixture
+'''6.''' Once focused fix the each lens with a drop of super glue.'''Test the lenses after several minutes to ensure they have taken the glue and cannot be moved'''
-'''7.''' Once focused fix the each lens with a drop of super glue.'''Test the lenses after several minutes to ensure they have taken the glue and cannot be moved'''
+'''7.''' Remove the assembly from the test fixture, remove I/O test board
 '''8.''' Advance the Main Board Assembly to the Driver Side Case Assembly Station.
-<br/><br/><br/><br/>
+<br/>