Manufacturing:X2 Camera Top Level Assembly - Revision history

Mark: Blanked the page

2015-07-17T19:31:20Z

Blanked the page

Mark: /* Driver Side Case Assembly */

2015-07-17T19:30:26Z

Driver Side Case Assembly

Mark: /* Driver Side Case Assembly */

2015-07-17T19:18:01Z

Driver Side Case Assembly

Mark: Created page with "==Idrive X2 Camera Top Level Assembly== ===Driver Side Case Assembly=== {| class="wikitable floatleft" |- !'''X2 Drive Side Case Materials''' |- |Driver Side Plastic Case |-..."

2015-07-17T19:14:17Z

Created page with "==Idrive X2 Camera Top Level Assembly== ===Driver Side Case Assembly=== {| class="wikitable floatleft" |- !'''X2 Drive Side Case Materials''' |- |Driver Side Plastic Case |-..."

New page

==Idrive X2 Camera Top Level Assembly==

===Driver Side Case Assembly===

{| class="wikitable floatleft"
|-
!'''X2 Drive Side Case Materials'''
|-
|Driver Side Plastic Case
|-
|LED Plastic Lens
|-
|X2 Main Board and LED Assembly
|-
|}

 

'''1.''' Snap the LED Lens into the Driver Side Case

::- Ensure that the two LED indents are towards the bottom of the camera

::- Clear LED lens is shown to enhance the view of indents

::- Actual LED Lens is black/opaque as shown

[[File:x2_led_lens_assy.jpg|320px|]]

 

'''2.''' Snap the LED Board Assembly into the Driver Side Case as shown

[[File:x2_led_assy_incase.jpg|300px|]]

 

'''3.''' Snap the X2 Main board Assembly into the Driver Side Case as shown

[[File:x2_main_driver_case.jpg|250px|]]

 

===Road Side Case Assembly===

{| class="wikitable"
|-
!'''X2 Road Side Case Materials'''
|-
|Road Side Plastic case
|-
|Plastic Support Spur
|-
|Screw for Support Spur
|-
|FCC Compliance Label
|-
|}
{| class="wikitable floatcenter"
|-
!'''Electronic Module Materials'''
|-
|SparkLan WiFi Module
|-
|WiFi cable
|-
|Dual Band WiFi Antenna
|-
|Screws for WiFi mounting
|-
|GPS Module Assembly
|-
|}

'''1.''' Attach Base Support Spur to the Road Side Case with the screw (Note correct orientation of Support Spur)Place FCC compliance sticker as shown.

[[File:x2supportspur2.jpg|300px|]][[File:x2_fcc_compliance_sticker.jpg|300px|]]

'''2.''' Install the Wifi Module with cable and antenna, secure with 2 screws as shown

[[File:x2wifimodule1.jpg|300px|]][[File:x2wifimodule2.jpg|250px|]]

'''3.''' Install GPS Module as shown. Ensure the cable is routed properly so as to avoid he power connector opening.

[[File:x2gpsmodule1.jpg|320px|]][[File:x2gpsmodule2.jpg|320px|]]

 

===Top Level Camera Assembly===

{| class="wikitable"
|-
!'''X2 Top Level Camera Materials'''
|-
|Driver Side Case Assembly
|-
|Road Side Case Assembly
|-
|Bar Code Label with Serial Number
|-
|Plastic Dust Cover for Accessory Connectors
|-
|Case Screw
|-
|Wifi Antenna
|-
|}

'''1.''' Connect the GPS and WiFi Cables to the Main Board. Remove the backing tape from the wifi antenna and affix the Antenna on the Driver Side Case as shown.

[[File:X2wifiantenna.jpg|320px|]]

'''2.''' Snap the two halves of the camera together ensuring no cables interfere with or block the Lens, Power Connector, I/O Connectors, USB opening or case screw

[[File:x2wifiandgpsattachment.jpg|320px|]][[File:x2twohalves.jpg|320px|]]

'''3.''' Install Plastic Dust Cover for Accessory Connectors - move to after final test.

[[File:x2accessorycover.jpg|320px|]]

'''4.''' Secure the cases to together with the case screw. Do not over torque the screw.

[[File:x2casescrew1.jpg|320px|]]

 

===Windshield Support Assembly===

{| class="wikitable"
|-
!'''X2 Windshield Support Materials'''
|-
|Plastic Windshield Support
|-
|Plastic Support Back Plate
|-
|Screw for Support Back Plate
|-
|3M Adhesive Tape
|-
|Screw for Support attachment to Spur
|-
|Washer for Support Screw
|-
|Locknut for Support Attachment
|-
|}

'''1.''' Assemble Windshield Support Base Assembly (Windshield support not attached to the camera until after final test or else the power connector would be inaccessible

::* Snap plastic back plate into support

::* secure with screw

::* Apply 3M tape and trim flush with scaple

[[File:x2winshieldsupport2.jpg|300px|]][[File:x2winshieldsupport.jpg|320px|]] [[File:x2winshieldsupporttape.jpg|350px|]]

← Older revision		Revision as of 19:31, 17 July 2015
Line 1:		Line 1:
−	~~==Idrive X2 Camera Top Level Assembly==~~

−	~~===Driver Side Case Assembly===~~
−	~~This one?~~
−	~~{\| class="wikitable"~~
−	\|-
−	~~!'''X2 Drive Side Case Materials'''~~
−	\|-
−	~~\|Driver Side Plastic Case~~
−	\|-
−	~~\|LED Plastic Lens~~
−	\|-
−	~~\|X2 Main Board and LED Assembly~~
−	\|-
−	\|}
−
−
−	~~'''1.''' Snap the LED Lens into the Driver Side Case~~
−
−	~~::- Ensure that the two LED indents are towards the bottom of the camera~~
−
−	~~::- Clear LED lens is shown to enhance the view of indents~~
−
−	~~::- Actual LED Lens is black/opaque as shown~~
−
−
−	~~[[File:x2_led_lens_assy.jpg\|320px\|]]~~
−
−	~~<br/><br/>~~
−
−	~~'''2.''' Snap the LED Board Assembly into the Driver Side Case as shown~~
−
−	~~[[File:x2_led_assy_incase.jpg\|300px\|]]~~
−
−	~~<br/><br/>~~
−
−	~~'''3.''' Snap the X2 Main board Assembly into the Driver Side Case as shown~~
−
−	~~[[File:x2_main_driver_case.jpg\|250px\|]]~~
−
−
−	~~<br/><br/>~~
−
−	~~===Road Side Case Assembly===~~
−
−	~~{\| class="wikitable"~~
−	\|-
−	~~!'''X2 Road Side Case Materials'''~~
−	\|-
−	~~\|Road Side Plastic case~~
−	\|-
−	~~\|Plastic Support Spur~~
−	\|-
−	~~\|Screw for Support Spur~~
−	\|-
−	~~\|FCC Compliance Label~~
−	\|-
−	\|}
−	~~{\| class="wikitable floatcenter"~~
−	\|-
−	~~!'''Electronic Module Materials'''~~
−	\|-
−	~~\|SparkLan WiFi Module~~
−	\|-
−	~~\|WiFi cable~~
−	\|-
−	~~\|Dual Band WiFi Antenna~~
−	\|-
−	~~\|Screws for WiFi mounting~~
−	\|-
−	~~\|GPS Module Assembly~~
−	\|-
−	\|}
−
−
−	~~'''1.''' Attach Base Support Spur to the Road Side Case with the screw (Note correct orientation of Support Spur)Place FCC compliance sticker as shown.~~
−
−	~~[[File:x2supportspur2.jpg\|300px\|]][[File:x2_fcc_compliance_sticker.jpg\|300px\|]]~~
−
−
−	~~'''2.''' Install the Wifi Module with cable and antenna, secure with 2 screws as shown~~
−
−	~~[[File:x2wifimodule1.jpg\|300px\|]][[File:x2wifimodule2.jpg\|250px\|]]~~
−
−
−	~~'''3.''' Install GPS Module as shown. Ensure the cable is routed properly so as to avoid he power connector opening.~~
−
−	~~[[File:x2gpsmodule1.jpg\|320px\|]][[File:x2gpsmodule2.jpg\|320px\|]]~~
−
−
−	~~<br/><br/>~~
−
−
−
−	~~===Top Level Camera Assembly===~~
−
−	~~{\| class="wikitable"~~
−	\|-
−	~~!'''X2 Top Level Camera Materials'''~~
−	\|-
−	~~\|Driver Side Case Assembly~~
−	\|-
−	~~\|Road Side Case Assembly~~
−	\|-
−	~~\|Bar Code Label with Serial Number~~
−	\|-
−	~~\|Plastic Dust Cover for Accessory Connectors~~
−	\|-
−	~~\|Case Screw~~
−	\|-
−	~~\|Wifi Antenna~~
−	\|-
−	\|}
−
−	~~'''1.''' Connect the GPS and WiFi Cables to the Main Board. Remove the backing tape from the wifi antenna and affix the Antenna on the Driver Side Case as shown.~~
−
−	~~[[File:X2wifiantenna.jpg\|320px\|]]~~
−
−
−	~~'''2.''' Snap the two halves of the camera together ensuring no cables interfere with or block the Lens, Power Connector, I/O Connectors, USB opening or case screw~~
−
−	~~[[File:x2wifiandgpsattachment.jpg\|320px\|]][[File:x2twohalves.jpg\|320px\|]]~~
−
−	~~'''3.''' Install Plastic Dust Cover for Accessory Connectors - move to after final test.~~
−
−	~~[[File:x2accessorycover.jpg\|320px\|]]~~
−
−
−	~~'''4.''' Secure the cases to together with the case screw. Do not over torque the screw.~~
−
−	~~[[File:x2casescrew1.jpg\|320px\|]]~~
−
−	~~<br/><br/>~~
−
−	~~===Windshield Support Assembly===~~
−
−	~~{\| class="wikitable"~~
−	\|-
−	~~!'''X2 Windshield Support Materials'''~~
−	\|-
−	~~\|Plastic Windshield Support~~
−	\|-
−	~~\|Plastic Support Back Plate~~
−	\|-
−	~~\|Screw for Support Back Plate~~
−	\|-
−	~~\|3M Adhesive Tape~~
−	\|-
−	~~\|Screw for Support attachment to Spur~~
−	\|-
−	~~\|Washer for Support Screw~~
−	\|-
−	~~\|Locknut for Support Attachment~~
−	\|-
−	\|}
−
−	~~'''1.''' Assemble Windshield Support Base Assembly (Windshield support not attached to the camera until after final test or else the power connector would be inaccessible~~
−
−	~~::* Snap plastic back plate into support~~
−
−	~~::* secure with screw~~
−
−	~~::* Apply 3M tape and trim flush with scaple~~
−
−
−	~~[[File:x2winshieldsupport2.jpg\|300px\|]][[File:x2winshieldsupport.jpg\|320px\|]] [[File:x2winshieldsupporttape.jpg\|350px\|]]~~
−
−
−	~~<br/><br/>~~

@@ Line 2: / Line 2: @@
 ===Driver Side Case Assembly===
+This one?
 {| class="wikitable"
 |-

@@ Line 3: / Line 3: @@
 ===Driver Side Case Assembly===
-{| class="wikitable floatleft"
+{| class="wikitable"
 |-
 !'''X2 Drive Side Case Materials'''
@@ Line 14: / Line 14: @@
 |-
 |}