Idrive Installer Processes and Guidelines - Revision history

Jeff: /* D4 Installation */

2013-10-17T16:13:55Z

D4 Installation

2013-10-17T15:56:38Z

D4 Installation

2013-10-17T15:42:32Z

D4 Installation

2013-10-17T15:41:41Z

D4 Installation

2013-10-17T15:39:03Z

D4 Installation

2013-10-17T15:33:06Z

D4 Installation

2013-10-16T20:42:55Z

D4 Installation

2013-10-16T19:24:04Z

D4 Installation

2013-10-16T19:00:44Z

D4 Installation

2013-10-16T18:32:32Z

D4 Installation

← Older revision		Revision as of 16:13, 17 October 2013
Line 114:		Line 114:
	12) Push record on the remote and verify that it can write to the hard drive.		12) Push record on the remote and verify that it can write to the hard drive.

−	~~14) Using the remote control.~~	+

@@ Line 103: / Line 103: @@
 ) All so supply will be a in-line fuse that will be connected to constant 12V red wire.
 ) Once all connections to the D4 have been made you will need to a line the cameras.
-) In order to do this you will need a monitor connected to the output of the D4.
+) In order to do this you will need a monitor connected to the output on the D4.
 ) Using the monitor check that the image from the cameras is level and that you are getting full coverage.
 ) Check that the date and time are set correctly.
 ) Push record on the remote and verify that it can write to the hard drive.
 ) Using the remote control.

@@ Line 102: / Line 102: @@
 ) Use a volt meter to check for constant 12V and switched 12V.
-) Al so supply will be a in-line fuse that will be connected to constant 12V red wire.
+) All so supply will be a in-line fuse that will be connected to constant 12V red wire.
 ) You will need to connect the fuse using a butt connector not supplies.

@@ Line 90: / Line 90: @@
 ==D4 Installation==
 <br\><br\>
-) Confirm with customer as to the location of the D4 and cameras.
+) Confirm as to the location of the D4 and cameras.
 ) Make sure that the mounting locations will not interfere with safe operation of the vehicle.

← Older revision		Revision as of 15:39, 17 October 2013
Line 112:		Line 112:
	11) Using the monitor check that the image from the cameras is level and that you are getting full coverage.		11) Using the monitor check that the image from the cameras is level and that you are getting full coverage.

−	00) Check that the date and time ~~are set correctly.~~	+	12) Check that the date and time are set correctly.
−
−	~~13) Using the remote control.~~
−
−	~~00) The remote control most be pointed at the front of the D4.~~
−
−	~~12) Check that all idrive settings including the date time and Time zone~~ are set correctly.

		+	13) Push record on the remote and verify that it can write to the hard drive.

		+	14) Using the remote control.

← Older revision		Revision as of 20:42, 16 October 2013
Line 118:		Line 118:
	00) The remote control most be pointed at the front of the D4.		00) The remote control most be pointed at the front of the D4.

−	~~00)~~
−
−	~~14) If your are using a laptop you will need Amcap software.~~
−
−	~~15) Once the laptop is connected to the D4 Will need to open Amcap software to view D4 outputs.~~
−
−	~~16) If you do not have Amcap loaded on your computer you can download it from the idrive admin Center under downloads.~~
−
−	~~17) You Will need to make sure that the key in the D4 is turned the on position and that the ignition for the vehicle is also in the on position.~~
−
−	~~18) Once you have seen the Idrive splash come up on the screen you can use the remote control to check and change any settings.~~


	<br\><br\>		<br\><br\>

@@ Line 108: / Line 108: @@
 ) Once all connections to the D4 have been made you will need to a line the cameras.
 ) In order to do this you will need a monitor of some sort connected to the output of the D4.
-) Thin check that all idrive settings including the date, time and Time zone are set correctly.
+) Using the monitor check that the image from the cameras is level and that you are getting full coverage.
-) This is don by using the remote control.
+) Thin check that all idrive settings including the date, time and Time zone are set correctly.
-) If your are using a laptop you will need Amcap software.
+) This is don by using the remote control.
-) Once the laptop is connected to the D4 Will need to open Amcap software to view D4 outputs.
+) The remote control most be pointed at the front of the D4.
-) If you do not have Amcap loaded on your computer you can download it from the idrive admin Center under downloads.
+)
-) You Will need to make sure that the key in the D4 is turned the on position and that the ignition for the vehicle is also in the on position.
+) If your are using a laptop you will need Amcap software.
-) Once you have seen the Idrive splash come up on the screen you can use the remote control to check and change any settings.
+) Once the laptop is connected to the D4 Will need to open Amcap software to view D4 outputs.
 <br\><br\>