Firmware loading and test procedures - Revision history

Mark at 16:39, 9 January 2013

2013-01-09T16:39:30Z

2012-09-07T07:42:06Z

Materials Requirement by Station

2012-09-07T07:41:49Z

Exploded View of an idrive X1

2012-09-07T07:41:24Z

Exploded View of an idrive X1

2012-09-07T07:41:16Z

Assembly Station Workflow Chart

2012-09-07T07:41:02Z

Important Information

2012-09-07T07:38:46Z

Process Station 8 – Final Test Station Initialization

2012-09-07T07:38:36Z

Process Station 8 - Final Testing of Idrive X1

2012-09-07T07:38:23Z

Automatic Mode ~5:20 with single camera

2012-09-07T07:38:12Z

Manual Mode portion ~5:00 with single camera

@@ Line 161: / Line 161: @@
 * Network Adapters LAN settings:
-'''Connection one for the Programming Fixture (must use crossover cat5 cable)'''
+'''Connection one for the Programming Fixture '''
 IP address: 192.168.0.10

@@ Line 25: / Line 25: @@
 ==Materials Requirement by Station==
-[[File:Materials.JPG|700px]][[File:Cont.JPG|700px]]
+<br/><br/>
 ==Equipment Requirements and Setup==

@@ Line 22: / Line 22: @@
 [[File:View.jpg|700px|]]
-<br/><br/>
+<br/><br/><br/>
 ==Materials Requirement by Station==

← Older revision		Revision as of 07:41, 7 September 2012
Line 22:		Line 22:

	[[File:View.jpg\|700px\|]]		[[File:View.jpg\|700px\|]]
		+	<br/><br/>

	==Materials Requirement by Station==		==Materials Requirement by Station==

← Older revision		Revision as of 07:41, 7 September 2012
Line 9:		Line 9:

	* Each Idrive X1 motherboard will be uniquely paired to one wifi module and one remote button that are assigned to each other during the process. Under no circumstances can you use them with another idrive X1 board! If you need to do that you need to reformat the SD card and perform the installation process from the beginning (the Idrive SN is the WiFi MAC). Never reuse a Wifi Module after Station 8 because this will create a duplicate serial number (Wifi MAC address) in the global center.		* Each Idrive X1 motherboard will be uniquely paired to one wifi module and one remote button that are assigned to each other during the process. Under no circumstances can you use them with another idrive X1 board! If you need to do that you need to reformat the SD card and perform the installation process from the beginning (the Idrive SN is the WiFi MAC). Never reuse a Wifi Module after Station 8 because this will create a duplicate serial number (Wifi MAC address) in the global center.
		+
		+	<br/><br/>

	==Assembly Station Workflow Chart==		==Assembly Station Workflow Chart==

@@ Line 621: / Line 621: @@
 [[File:Test board.jpg]]
-----
+<br/><br/>
 ===Process Station 8 - Final Testing of Idrive X1===

@@ Line 624: / Line 624: @@
 ===Process Station 8 - Final Testing of Idrive X1===
+<br/><br/>
 ====Automatic Mode ~5:20 with single camera====
+<br/>
 Note - Manual Mode is used in conjunction with Automatic mode to test shock and panic events. There is no automatic way to press the panic button or shake the camera(s)

← Older revision		Revision as of 07:38, 7 September 2012
Line 657:		Line 657:

	'''13.''' Turn Off the Power Toggle Switch (Right Position)		'''13.''' Turn Off the Power Toggle Switch (Right Position)
		+	<br/><br/><br/>

	====Manual Mode portion ~5:00 with single camera====		====Manual Mode portion ~5:00 with single camera====

← Older revision		Revision as of 07:38, 7 September 2012
Line 691:		Line 691:

	'''29.''' Advance the Idrive devices to the next station.		'''29.''' Advance the Idrive devices to the next station.
		+	<br/><br/>

	====Full Manual Mode====		====Full Manual Mode====