D8 Initial Configuration and Setup - Revision history

Mark: /* Configure the Default Parameters using a param.xml file */

2017-03-22T19:35:35Z

Configure the Default Parameters using a param.xml file

2017-03-22T19:18:32Z

Device Specific Settings

2017-03-21T22:41:01Z

Assemble System

2017-03-20T22:16:51Z

Device Specific Settings

2017-03-20T22:15:45Z

Device Specific Settings

2017-03-20T20:48:02Z

Items needed

2017-03-20T19:05:47Z

Assemble System

2017-03-20T17:21:39Z

Installation Issues

2017-03-20T17:20:55Z

Hard Drive Installation

2017-03-20T17:19:50Z

Hard Drive Installation

@@ Line 107: / Line 107: @@
 ==Configure the Default Parameters using a '''param.xml''' file==
-Stage the param.xml file on an SD card or the SSD
+Current file is '''param_032217.xml'''
 Power on the D8

← Older revision		Revision as of 19:18, 22 March 2017
Line 151:		Line 151:
	:*company_name (Sys Setup>>Terminal>>Company)		:*company_name (Sys Setup>>Terminal>>Company)

−	~~:*SimICCID (~~

		+	<br><br>

		+	==Save settings in new Param.xml file==

		+	(Tools>>Parameters>>Parameters Export) click yes to overwrite the generic file

	<br><br>		<br><br>

← Older revision		Revision as of 22:41, 21 March 2017
Line 32:		Line 32:

	Place default configuration (Parameters file on the SSD) (Figure out how to use an SD card for this)		Place default configuration (Parameters file on the SSD) (Figure out how to use an SD card for this)
		+
		+	Looks like the hard drive needs to be powered up in the D8 so the two partitions can be created. Then put the param.xml file on it.

	<br><br>		<br><br>

@@ Line 140: / Line 140: @@
 Set Customer/Device Specific Parameters==
 :*company_name (Sys Setup>>Terminal>>Company)
-:*SimICCID
+:*SimICCID (

← Older revision		Revision as of 22:15, 20 March 2017
Line 142:		Line 142:

	:*company_name (Sys Setup>>Terminal>>Company)		:*company_name (Sys Setup>>Terminal>>Company)
		+
		+	:*SimICCID

@@ Line 19: / Line 19: @@
 ==Items needed==
-D8 Kit
+:*D8 Kit
-SSD
+:*SSD
-BNC to RCA adaptor
+:*BNC Male to RCA Male adapter
-SIM card
+:*SIM card
 <br><br>

← Older revision		Revision as of 19:05, 20 March 2017
Line 14:		Line 14:

	[[file:document_ser_number1.jpg‎\|300px\|left\|Doc Serial Number]]		[[file:document_ser_number1.jpg‎\|300px\|left\|Doc Serial Number]]
		+
		+	<br><br>
		+
		+	==Items needed==
		+
		+	D8 Kit
		+
		+	SSD
		+
		+	BNC to RCA adaptor
		+
		+	SIM card

	<br><br>		<br><br>

← Older revision		Revision as of 17:21, 20 March 2017
Line 394:		Line 394:

	Connect what? Don't connect what?		Connect what? Don't connect what?
		+
		+	<br><br>
		+
		+	==Monitor Information==
		+
		+	We are shipping a 7" monitor with the first 3 D8s.
		+
		+	Voltage input 9v - 35vdc, 5W
		+
		+	Wiring:
		+
		+	:*Red 9-35vdc
		+
		+	:*Black Gnd
		+
		+	:*Yellow - video1
		+
		+	:*Yellow - Video2
		+
		+	:* Blue - Rear View

	<br><br>		<br><br>

@@ Line 29: / Line 29: @@
 [[File: D8sled1.jpg|x250px|alt=Alt text|Four screws need to dismantle the sled]]
 [[File: D8sled2.jpg|x250px|alt=Alt text|Inside of the hard drive sled]]
 Next, remove the screws from both silver brackets, take them off of the main sled, and set them aside.
@@ Line 34: / Line 35: @@
 [[File: D8sled3.jpg|x250px|alt=Alt text|Screws holding in the silver brackets]]
 [[File: D8sled4.jpg|x250px|alt=Alt text|Sled without one bracket]]
 Now, locate the hard drive standoffs from the D8 accessory kit.  Screw four of them into the sides of the hard drive to be installed.
@@ Line 39: / Line 41: @@
 [[File: D8sled5.jpg|x250px|alt=Alt text|Hard drive standoff]]
 [[File: D8sled6.jpg|x250px|alt=Alt text|SSD with standoffs installed]]
 Take the silver brackets and fit them onto the hard drive standoffs.  Make sure the indentation is facing inward, towards the hard drive.  At this point you should also connect the SATA cable to the drive.
 [[File: D8sled7.jpg|x250px|alt=Alt text|Hard drive with brackets]]
 Finally, slide the hard drive and brackets back into place inside the sled.  Re-fasten the bracket screws and reassemble the sled.