View source for New D4M (4/17/19) Initial Configuration and Setup

=Idrive D4M Configuration=

<br>

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

<br><br><br><br><br><br>

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

<br><br><br><br><br><br><br><br><br><br><br>

*Enter Serial Number into Admin Center. 

::<span style="color: green">AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type  '''IDRDVRD4HD'''

<br><br>

==Install Hard Drive/SSD==

[[File:SSDinD4.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M


<br><br>

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

<br>

[[File:HDMIvsCVBS.JPG|right|450px]]


::1)*Plug in a Mouse into the USB port on the left hand side of the Front Panel (no Remote Control with the D4M)

<br><br><br><br><br><br>
<div style="text-align: right; direction: ltr; margin-left: 1em;">When plugging in Monitor you can use the provided Composite Video (NTSC output) and connect to the USB Video capture device using AMCAP... <br> or if your monitor has an open HDMI input the image will be full screen and the Mouse will be easier to point on a large Desktop 21" Monitor </div>

<br><br>

::In the Rear Panel>

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

<br><br><br><br>


[[file:Alarmcble5.png‎|left|px250]]
<br><br>

::1)*Confirm that the Alarm Wire SNR1 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

[[File:Settings.AlarmSetting.JPG|right]]



'''NOTE: this will only function after the CFG is loaded to the D4M'''

see pic on right after cfg is loaded

<br><br><br><br><br><br><br><br>
<br><br><br><br>
<br><br><br><br>
<br><br><br><br>

===Click the Right Mouse Button For Options=== 

[[file:D4M_Right_Click.jpg|left|100px|]]


::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

<br><br><br><br>

==Verify Correct Firmware version==

<span style="color: green"> Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

*<span style="color: green"> Main Menu> System> System Upgrade> Browse and select file and click OK


[[file:D4M_FW_Update.jpg‎|left|300px|]]

<br>

==Import Idrive Default Configuration==

'''*Download the Latest Config File''' [[media:Hidvr.zip|hidvr.zip]]

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR



'''Note: if the SD has been used in another Deck it might have 2 additional files... if so only select the Hidvr.cfg'''
[[File:SD CFG.JPG]]



*<span style="color: green"> Main Menu> System> Config Operation>
:<span style="color: green">'''Import Configuration Browse and select file "hidvr.cfg" and click OK'''


'''Note: this will only take a second and may or may not appear to change the screen, but it is finished.'''


Hit return on the bottom to return to the previous menu

[[File:System.Config.Import.SD.hidvr.cfg.jpg]]
<br>

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID”

:<span style="color: green">'''Menu> Mobile> Motor> License ID'''

[[File:Mobile.MotorSetting.JPG ]]



*Set the Customer's Time Zone
:<span style="color: green"> '''Menu> Setting> Date/Time> Timezone'''
*Set the Customer's Time

:<span style="color: green"> '''Menu> Setting> Date/Time> Set Time'''
*Set the Customer's Daylight Savings Time

:<span style="color: green"> Menu> '''Setting> DST Setting> USA'''

::'''Note''' Selecting USA sets DST Correctly

[[File:Settings.Date.Time.JPG ]]


'''IMPORTANT! Click on APPLY before leaving screen or restarting'''


*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive <span style="color: green"> Menu> Storage> Disk Info> Format

::<span style="color: red">The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

<br><br><br><br>

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Server related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.


<br><br><br><br><br><br><br>

==Preview==




===Camera Settings===

Each channel set separately 

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost <span style="color: blue"> '''OFF'''

::2)* Camera Title - <span style="color: blue"> '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - <span style="color: blue"> '''AUTO DETECT'''

::4)*Power Line Frequence - <span style="color: blue"> '''?'''

::5)*Frame Rate - <span style="color: blue"> '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical <span style="color: blue"> '''OFF,OFF'''

::7)*Brightness *<span style="color: blue"> '''DEFAULT (50)'''

::8)*Contrast - <span style="color: blue"> '''DEFAULT (40)'''

::9)*Hue - <span style="color: blue"> '''DEFAULT (50)'''

::10)*Saturation - <span style="color: blue"> '''DEFAULT (50)'''

::11)*Audio Volume - <span style="color: blue"> '''DEFAULT (40)'''

::12)*Auto Black-and-White - At night switch to Black and White mode <span style="color: blue"> '''OFF'''

::13)*FrameRate Down - lower frame rate at night<span style="color: blue"> '''OFF'''

::14)*IR LED Light - Only if supported by the camera<span style="color: blue"> '''AUTO'''

::15)*LED Status Indicator - <span style="color: blue"> '''OFF'''

<span style="color: red"> '''Copy To, Apply, Return Buttons''' not shown in AMCAP

<br>

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately 

::1)*Motion Zone Settings <span style="color: blue"> '''All Clear'''

::2)* Enable Adaptive Bit rate <span style="color: blue"> '''Default'''

::3)* Record when motion detection triggered <span style="color: blue"> '''Default'''

::4)* Alarm Buzzer <span style="color: blue"> '''Default'''

::5)* Sensitivity(0-100) <span style="color: blue"> '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) <span style="color: blue"> '''Default(10)'''

<br><br><br><br><br><br><br><br><br><br><br>

<span style="color: red"> '''Copy To, Apply, Return Buttons''' not shown in AMCAP

<br><br><br>

==Record==

[[File:Record.RecordDetails.JPG|left|400px|]]

::1)* Resolution - <span style="color: blue"> '''DEFAULT(BASIC,2/3D1)'''
::2)* Bitrate(Kbps) - <span style="color: blue"> '''DEFAULT(200)'''
::3)* Frame Rate(1-30) - <span style="color: blue"> '''DEFAULT(30)'''
::4)* Real Frame Rate - <span style="color: blue"> '''30'''
::5)* File Length(Minutes) - <span style="color: blue"> '''5 (Set 5 on all  4 Channels)'''
::6)* Record with Audio - <span style="color: blue"> '''YES (Set YES on all  4 Channels)'''
::7)* Record Mode - <span style="color: blue"> '''DEFAULT(AUTO)'''
::8)* Size(MBytes/hour) - <span style="color: blue"> '''DEFAULT(710)'''
::9)* Camera Status - <span style="color: blue"> '''DEFAULT (Monitored,OK)'''
::10)* Record Status - <span style="color: blue"> '''DEFAULT (Monitored,Recording)'''
::11)* Stop All Stop - <span style="color: blue"> '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - <span style="color: blue"> '''DEFAULT(Blank)'''

<br><br><br>

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM   HH:MM Leave this section blank - <span style="color: blue"> '''DEFAULT'''


<br><br><br><br><br><br><br><br><br><br><br><br><br><br>

<span style="color: red"> '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP


<br><br>

==Storage==

[[File:Storage.BaseSetting.JPG|left|400px|]]

::1)* Overwrite Mode - <span style="color: blue"> '''DEFAULT(Overwrite normal video)'''

::2)* No disk alarm time(seconds)) - <span style="color: blue"> '''CFG sets to 60 seconds (ON)'''

::'''This tells the client that the Disk is not in the unit, or that the HDD has become non-accessible  - beeps one time 60 seconds after start up if missing 
'''

::3)* Normal Record Disk - <span style="color: blue"> '''DEFAULT(sata)'''
::4)* Alarm Record Disk - <span style="color: blue"> '''DEFAULT(sata)'''
::5)* Format - <span style="color: blue"> '''Use Format Only at Initialization of SSD'''

<br><br><br><br><br><br><br><br><br><br>


<br><br><br>

==Mobile==

[[File:Mobile.PowerSetting.JPG|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - <span style="color: blue"> '''DEFAULT(High)'''
::2)* ACC Power Off Delay(seconds)) - <span style="color: blue"> '''CFG set to 1 Second'''
::3)* Sleep Delay-ACC Off(seconds) - <span style="color: blue"> '''CFG set to 0'''
::4)* Sleep Delay-No Alarm(seconds) - <span style="color: blue"> '''CFG set to 0'''
::5)* Power On at(HH:MM) - <span style="color: blue"> '''00:00'''
::6)* Power Off at (HH:MM) - <span style="color: blue"> '''00:00'''
::7)* Current Voltage - <span style="color: blue"> '''13.3 (monitored)'''
::8)* Power Off Threshold Voltage - <span style="color: blue"> '''Set to 8VDC'''
::9)* Power On threshold Voltage - <span style="color: blue"> '''Set to 9VDC'''


<br>

==Motor==


::1)* License ID - <span style="color: blue"> '''ENTER S/N'''
::2)* Obtain Speed - <span style="color: blue"> '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - <span style="color: blue"> '''MPH'''
::4)* Speed Limit - <span style="color: blue"> '''65'''
::5)* Overspeed Record - <span style="color: blue"> '''DEFAULT'''
::6)* Overspeed OSD - <span style="color: blue"> '''SPD'''
::7)* Overspeed buzzer - <span style="color: blue"> '''Off'''


<br>

<span style="color: red"> ''' Apply, Return Buttons''' not shown in AMCAP

<br>

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]



::1)* GPS Status - <span style="color: blue"> '''DEFAULT(Monitored, Not Found)'''
::2)* GPS OSD - <span style="color: blue"> '''DEFAULT(On)'''
::3)* GPS Baudrate - <span style="color: blue"> '''DEFAULT(9600)'''
::4)* Sync with GPS time - <span style="color: blue"> '''Check'''


<span style="color: red"> ''' Apply, Return Buttons''' not shown in AMCAP


<br><br><br>
<br><br><br>

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - <span style="color: blue"> '''DEFAULT(Monitored)'''
::2)* Initial Offset - <span style="color: blue"> '''DEFAULT(0,0,-1 TBD)'''
::3)* Alarm Threshold - <span style="color: blue"> '''DEFAULT(0,0,0 TBD)'''
::4)* Alarm Buzzer - <span style="color: blue"> '''DEFAULT(TBD)'''
::5)* Alarm Record - <span style="color: blue"> '''DEFAULT(TBD)'''

<br><br><br>

<span style="color: red"> ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP



<br><br><br><br>
<br><br><br><br>

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - <span style="color: blue"> '''DEFAULT(Monitored,Module Not Found) '''
::2)* Dial Enable - <span style="color: blue"> '''DEFAULT(Check))'''
::3)* Dial Number - <span style="color: blue"> '''DEFAULT(Blank)'''
::4)* APN - <span style="color: blue"> '''DEFAULT(Blank)'''
::5)* Username - <span style="color: blue"> '''DEFAULT(Blank)'''
::6)* Password - <span style="color: blue"> '''DEFAULT(Blank)'''



<span style="color: red"> ''' Apply, Return Buttons''' not shown in AMCAP


[[File:D4M_Network_Wifi.png|left|400px|]]

<br><br><br><br>

::'''WiFi'''

::1)* Enable - <span style="color: blue"> '''DEFAULT(Uncheck)'''
::2)* Mode - <span style="color: blue"> '''DEFAULT(Do not Select)'''
::3)* WiFi Status - <span style="color: blue"> '''Monitored, Module not found'''
::4)* WiFi IP - <span style="color: blue"> '''DEFAULT(Blank)'''
::5)* SSID - <span style="color: blue"> '''DEFAULT(Blank)'''
::6)* WiFi List - <span style="color: blue"> '''DEFAULT(Blank)'''
::7)* AP Scan - <span style="color: blue"> '''DEFAULT'''
::8)* Signal Strength - <span style="color: blue"> '''DEFAULT'''
::9)* Password - <span style="color: blue"> '''DEFAULT'''
::10)* IP - <span style="color: blue"> '''DEFAULT(192.168.33.1 TBD)'''
::11)* AP SSID - <span style="color: blue"> '''DEFAULT(HDVR, TBD)'''
::12)* Password - <span style="color: blue"> '''DEFAULT'''


<span style="color: red"> ''' Apply, Refresh, Return Buttons''' not shown in AMCAP


[[File:D4M_Network_LAN.png|left|400px|]]

<br>

::'''LAN'''

::1)* DHCP - <span style="color: blue"> '''DEFAULT(Uncheck)'''
::2)* IP - <span style="color: blue"> '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - <span style="color: blue"> '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - <span style="color: blue"> '''DEFAULT(192.168.0.1)'''



<span style="color: red"> ''' Apply, Return Buttons''' not shown in AMCAP



[[File:D4M_Network_Server_Settings.png|left|400px|]]

<br><br><br><br><br>

::'''Server Settings'''

::1)* Server Status - <span style="color: blue"> '''DEFAULT(Monitored, Disconnected)'''
::2)* Client DVR ID - <span style="color: blue"> '''DEFAULT(S/N)'''
::3)* Server - <span style="color: blue"> '''DEFAULT(192.168.0.128)'''
::4)* Server Port - <span style="color: blue"> '''DEFAULT(10000)'''
::5)* Channel - <span style="color: blue"> '''DEFAULT(1)'''
::6)* Resolution - <span style="color: blue"> '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - <span style="color: blue"> '''DEFAULT(100)'''
::8)* Framerate(1-30) - <span style="color: blue"> '''DEFAULT(10)'''
::9)* Talkback Channel- <span style="color: blue"> '''DEFAULT(1)'''


<span style="color: red"> ''' Apply, Return Buttons''' not shown in AMCAP


[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

<br><br>

::'''GPS Server Settings'''

::1)* GPS Network ID - <span style="color: blue"> '''DEFAULT(S/N)'''
::2)* GPS Server IP - <span style="color: blue"> '''DEFAULT'''
::3)* GPS Server Port - <span style="color: blue"> '''DEFAULT(0)'''
::4)* GPS Server Status - <span style="color: blue"> '''DEFAULT(Monitored,Disconnected)'''



<span style="color: red"> ''' Apply, Return Buttons''' not shown in AMCAP

<br><br><br><br><br><br><br>
<br><br><br><br><br><br><br>

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - <span style="color: blue"> '''Enable(Check)'''
::2)* DVR Time Display - <span style="color: blue"> '''Enable(Check)'''
::3)* USB Auto Update - <span style="color: blue"> '''DEFAULT(Not checked)'''
::4)* Language Mode - <span style="color: blue"> '''English'''
::5)* GUI Skin - <span style="color: blue"> '''Black'''
::6)* Transparent - <span style="color: blue"> '''Translucent'''
::7)* AHD Camera Num - <span style="color: blue"> '''4'''


<span style="color: red"> ''' Apply, Return Buttons''' not shown in AMCAP


<br><br><br>


[[File:Settings.AlarmSetting.JPG|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - <span style="color: blue"> '''Sensor1'''
::2)* Trigger Level/Mode - <span style="color: blue"> '''High'''
::3)* Alarm Record - <span style="color: blue"> '''Set'''
::4)* Alarm Snapshot - <span style="color: blue"> '''Set'''
::5)* Alarm OSD - <span style="color: blue"> '''DEFAULT(BACKING)'''
::6)* Alarm Buzzer - <span style="color: blue"> '''DEFAULT(OFF)'''
::7)* Switch View - <span style="color: blue"> '''DEFAULT(2) - this takes Channel 2 Full  Screen when wire in engaged with 12VDC'''
::8)* Switch View Delay(Seconds) - <span style="color: blue"> '''0'''
::9)* Pre-record Time(Seconds) - <span style="color: blue"> '''20'''
::10)* Post-record Time(Seconds) - <span style="color: blue"> '''15'''






[[File:Settings.Date.Time.JPG|left|400px|]]

::'''DST Settings'''

::1)* Date Format- <span style="color: blue"> '''mm-dd-yyyy'''
::2)* DVR Time - <span style="color: blue"> '''DEFAULT'''

'''NOTE: set Time Zone (US Eastern, Central, Mountain or Pacific) and DST USA first before Actual Client Time; '''

::3)* Set Time - <span style="color: blue"> '''DEFAULT(Input current date and time)'''
::4)* Time Zone - <span style="color: blue"> '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - <span style="color: blue"> '''0'''
::6)* DST Period - <span style="color: blue"> '''Yes'''
::7)* DST Setting - <span style="color: blue"> '''USA'''
::8)* From - <span style="color: blue"> '''DEFAULT(User Input)'''
::9)* To - <span style="color: blue"> '''DEFAULT(User Input)'''

<br><br>






[[File:Settings.Output.JPG|left|400px|]]

::'''Output Setting'''

::1)* Output Device - <span style="color: blue"> '''CVBS NTSC'''
'''NOTE: this will set by the Config File installation to NTSC so you can use AMCAP and USB Video Adapter

'''DO NOT use PAL in the US with 7" US Monitors'''

::2)* CVBS Output Volume(0-255) - <span style="color: blue"> '''16 ?'''
::3)* CVBS Output Reduction Value - <span style="color: blue"> '''0'''
::4)* ScreenSaver Delay(Seconds) - <span style="color: blue"> '''0'''

<br><br>



[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

<br><br><br><br><br><br>

::'''PTZ Settings'''


Apply the following to all four channels.

::1)* CH:01 - <span style="color: blue"> '''Baudrate 9600'''
::2)* CH:02 - <span style="color: blue"> '''Protocol PELCO-D'''
::3)* CH:03 - <span style="color: blue"> '''Address 0'''
::4)* CH:04 - <span style="color: blue"> '''DEFAULT'''

<br><br>

<span style="color: red"> ''' Copy to, apply, Return Buttons''' not shown in AMCAP





<br><br><br><br><br><br><br>

==File==

[[File:D4M_File.png|left|400px|]]


::'''File'''

No Setup needed.


<br><br><br><br><br><br><br><br><br><br><br><br><br><br>

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - <span style="color: blue"> '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - <span style="color: blue"> '''08/04/2018-0d'''
::3)* Camera1 Version - <span style="color: blue"> '''NTSC'''

<br>

<span style="color: red"> ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

<br><br><br><br><br><br><br><br>

::'''System Upgrade'''


::1)* Current Version - <span style="color: blue"> '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - <span style="color: blue"> '''DEFAULT(Browse)'''

<br><br><br><br><br><br>

<span style="color: red"> ''' Upgrade, Return Buttons''' not shown in AMCAP


<br><br><br><br>


[[File:System.Config.Import.SD.hidvr.cfg.jpg|left|400px|]]

<br><br>

Click the link below for D4M Idrive Configuration Downloading and Installation


[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Import_Idrive_Default_Configuration|'''Configuration''']] - Download and Install Idrive Client Configuration

<br><br><br><br><br><br><br><br><br><br><br>



[[File:D4M_System_Log.png|left|400px|]]

<br><br><br><br><br><br>

::'''System Log'''

::1)* DISPLAYS LOG - <span style="color: blue"> '''DEFAULT(Refresh only if necessary)'''

<br><br><br><br>

<span style="color: red"> ''' Refresh, Return Buttons''' not shown in AMCAP

<br><br><br><br><br><br><br><br>