View source for ICV D8 Initial Configuration and Setup

=ICARvisions D8 Initial Configuration=

<br><br>

==Configure/Document Hardware==

<br>

===Document Model Number, Serial number, SIM Card number===

Record them where? A/C, AWS, Pod systems - need RO support for this.

<br>

===Hard Drive Installation/Configuration===

Install SSD in in the D8 tray ans secure with the 4 supplied screws


<br>

====Format Hard drive '''EXT3''' (Linux filesystem)====

* Format the hard drive in the D8 Tools>Format (an unformatted HDD will show 0MB capacity)

or 

* Format the hard drive in a Linux system (use VMware/Ubuntu)

::Launch VMWare - Ubuntu

::Plug hard drive into USB with adaptor

::Click Player>Removable Devices>Sunplus Inovation USB to Serial-ATA Bridge and Disconnect from host 


<br>

===Install Batteries (not included)in the remote control===

*requires 2 AAA batteries

<br>

===Plug in the power supply harness===

<span style="color: red"> '''Power connector's plastic is keyed the same as Easystorage(D4)as well as the VisionMaster D8 and  but the pinouts are different!'''

[[File:icv8_power_conn.jpg|400px|]]

<br>

===Connect a monitor or Computer===

Plug supplied Monitor cable into the front of the D8

Connect Monitor cable to either:

:*External Monitor (Connect Yellow for video and black for monitor power)

:*For Laptop connection use StarTech USB to Svideo Video adapter with AMCAP Capture software (Connect yellow video connector requires Male to Male RCA adatpter)

:*plug Cat5 cable into device,Use Web browser - navigate to 192.168.0.250 (''' need to verify if this is default with a new D8''')


<br><br>

===Remove Sensor Cable and other unused options===

The cable will not be used by BNSF. Remove it and keep at Idrive in case needed in the future

<br><br>

=System Configuration=

Power up the device

<br>

==Logging into D8 System==

'''Notes:''' 

::*when you login recording will stop

::*If you disconnect AMCAP or Monitor the user remains logged in so it will not record until the session times out.


Press the "Login" Button on the remote.

Default login: '''Admin''' user default passwd '''888888'''

<br>

<span style="color: blue">For Configuration:<span style="color: red"> User name 6 letters/numbers max

<span style="color: blue"> *I propose we change "Admin" user to  '''"Idrive"''' with a password of '''"idrd8adm"''' . This login would be used by Idrive Support only.

<span style="color: red"> I renamed the user on my system but cannot change the password!

<br>

<span style="color: blue"> *Create a user called '''BNSF''' for the location manager to use. This will not have full admin permissions, only what we would allow them to do what they need to. We need to identify what they need and how to set the permissions. - Mark

::*View, Copy videos

::*Next item

::*Next item


<br>

==Setup Menu==

The Setup Menu has 8 options

[[File:icvd8_setup_Menu.jpg|left|350px|]]

[[ICV D8 Initial Configuration and Setup#General|'''*General''']] - Basic info for: Device, Vehicle, User, Network, Display, OCD

[[ICV D8 Initial Configuration and Setup#Channel Mode|'''*Channel Mode''']] - 

[[ICV D8 Initial Configuration and Setup#Record|'''*Record''']] - Recording Settings

[[ICV D8 Initial Configuration and Setup#Alarm|'''*Alarm''']] - Alarm Settings

[[ICV D8 Initial Configuration and Setup#Tools|'''*Tools''']] - 

[[ICV D8 Initial Configuration and Setup#Peripherals|'''*Peripherals''']] - PTZ, Cellular, Wifi setup

[[ICV D8 Initial Configuration and Setup#Search|'''*Search''']] - Search for videos by Date/Time Etc.

[[ICV D8 Initial Configuration and Setup#System Info|'''*System Info''']]

<br>

===General===

The Basic setup menu has 6 options

[[File:icvd8_basic_setup.jpg|left|350px|]]

[[ICV D8 Initial Configuration and Setup#Date & Time|'''*Date & Time''']] - Date, Time, Daylight Savings, Timezone, Power Modes Etc.

[[ICV D8 Initial Configuration and Setup#Vehicle Info|'''*Vehicle Info''']] - Serial Number, Device_Number SIM- Number, Vehicle Number

[[ICV D8 Initial Configuration and Setup#User Setup|'''*User Setup''']] - User Management

[[ICV D8 Initial Configuration and Setup#Network|'''*Network''']] -  Network and server settings

[[ICV D8 Initial Configuration and Setup#Display|'''*Display''']] - On screen display, video out settings

[[ICV D8 Initial Configuration and Setup#Code OSD|'''*Code OSD]] - Per channel screen/video display

<br><br><br><br><br><br>

====Date & Time====

[[File:icvd8_date_time.jpg|left|350px|]]

*Date Format

*Time Format

*Daylight Savings Settings

*Time Mode - GPS

*Power Mode - Ignition

<br><br><br><br><br><br><br><br><br><br>

====Vehicle Info====

[[File:icvd8_vehicle_info.jpg|left|350px|]] Serial number of Device (Hex so not suitable for device number) Example 0000-0000-0002-20de

<span style="color: blue">'''*Dev-Num''' - '''must be 5 digits to integrate with server'''

*Department - Optional

*Driver Name - Optional

<span style="color: blue">'''*SIM-Num''' - field is only 12 digits long but SIM cards are 19 digits long. - figure it out

*Login IVMS check box - '''must Un-Check to use SIM Card'''

*Mile Accrual  - N/a

*Mileage - N/A

<span style="color: blue">'''*Vehicle-Num''' - vehicle name. can take letters as well as numbers. Set on server?

<br><br>

====User Setup====

[[File:icvd8_user_setup.jpg|left|250px|]]

Add/Remove users. Only the Admin User exists in the received device.

<span style="color: blue">*Setup a BNSF User.

<span style="color: blue">* change "Admin" to "Idrive" and non-defaut password?

<br><br><br><br><br><br><br><br><br><br>

====Network====

[[File:icvd8_network_setup.jpg|left|350px|]]

'''For Wired Cat5 connection ONLY''':

*IP Address
 
*Netmask
 
*Gateway
 
*MAC Address


'''For Wired, Wireless and Cellular connections''':

*Net Mode - search for Server by IP address or DNS

*Server Address - either IP Address or DNS Ex: dvr.idriveglobal.com

*Control Port - '''Must match the port of the "Gateway Server"'''


'''Other Options''': Intercom & IcCard - N/A


<br><br>

====Display====

[[File:icvd8_display_setup.jpg|left|350px|]]

<br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br>

====Code OSD====

[[File:icvd8_code_osd.jpg|left|350px|]]

Controls the text shown on screen/recordings

<span style="color: blue"> For BNSF each vehicle type will have different settings:

::   '''*SideHandler'''

::   '''*Chassis Handler'''

::   '''*Crane'''

<br><br><br><br><br><br><br><br><br><br><br><br>

===Channel Mode===

====Channel Mode Settings====

[[File:icvd8_channel_mode.jpg|left|350px|]]

<br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br>

===Record Settings===

[[File:icvd8_record_setup.jpg|left|350px|]]

[[ICV D8 Initial Configuration and Setup#Normal|'''*Normal''']] - Recording Basic Setup

[[ICV D8 Initial Configuration and Setup#Main Code|'''*Main Code''']] -Channels setup

[[ICV D8 Initial Configuration and Setup#Sub-Stream|'''*Sub-Stream''']] -

[[ICV D8 Initial Configuration and Setup#Record Plan|'''*Record Plan''']]- Timed recording schedule

[[ICV D8 Initial Configuration and Setup#SD Rec|'''*SD Rec''']] - Set backup to SD Card?

[[ICV D8 Initial Configuration and Setup#IPC|'''*IPC''']] - IP Camera Settings

<br><br><br><br><br>

====Normal====

<br>

====Main Code====

<br>

====Sub-Stream====

<br>

====Record Plan====

<br>

====SD Rec====

<br>

====IPC====

<br>

===Alarm Settings===

[[File:icvd8_alarm_setup.jpg|left|350px|]]

[[ICV D8 Initial Configuration and Setup#Sensor|'''*Sensor''']] - Configure & Assign input for wired alarms

[[ICV D8 Initial Configuration and Setup#Speed|'''*Speed''']] - Configure speed alarms

[[ICV D8 Initial Configuration and Setup#G-Sensor|'''*G-Sensor''']] - Configure accelerometer alarms

[[ICV D8 Initial Configuration and Setup#Temperature|'''*Temperature''']] - Configure temperature alarms

[[ICV D8 Initial Configuration and Setup#Alarm Out|'''*Alarm Out''']] - Configure & Assign output for wired alarms

[[ICV D8 Initial Configuration and Setup#Motion|'''*Motion''']] - Configure motion sensor alarms

[[ICV D8 Initial Configuration and Setup#Other Alarms|'''*Other Alarms''']] - Configure stationary or Fatigue alarms

<br><br><br><br>

====Sensor====

<br>

====Speed====

<br>

====G-Sensor====

<br>

====Temperature====

<br>

====Alarm Out====

<br>

====Motion====

<br>

====Other Alarm====

<br>

===Tools Settings===

[[File:icvd8_tools_menu.jpg|left|350px|]]

[[ICV D8 Initial Configuration and Setup#Configure|'''*Configure''']] - Import, Export, Default Config, Upgrade Logo

[[ICV D8 Initial Configuration and Setup#Format|'''*Format''']] - Format media

[[ICV D8 Initial Configuration and Setup#Log Search|'''*Log Search''']] - Search System/Alarm Logs

<br><br><br><br>

====Tools>Configure====


[[File:icvd8_tools_config.jpg|left|300px|]]

'''  *Default Config''' - restore all settings to factory default



'''  *Import Config File''' - Import configuration Settings From USB Stick

::Insert USB Stick with config file and Import (parameter.conf file is not ASCII)



'''  *Export Config File''' - Export Configuration Settings 

::Insert USB Stick and export.

::If no USB Stick the file is exported to the hard drive



'''  *Upgrade Logo''' - Import Logo (Boot Logo & Upgrading Logo)

::*Each Logo needs an Image size of 720x576 pix, Smaller than 256k, jpg format

::*required names: loading.jpg & upgrading.jpg

::*If images are on the USB stick at configuration time they should load

<br><br>

====Tools>Format====

500MB drive formatted in 2:45

<br>

====Tools>Log Search====

[[File:icvd8_log_search.jpg|left|300px|]]

<br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br>

===Peripherals Settings===

[[File:icvd8_peripherals_setup.jpg|left|350px|]]

[[ICV D8 Initial Configuration and Setup#PTZ Setup|'''*PTZ Setup''']] - 

[[ICV D8 Initial Configuration and Setup#Wireless Setup|'''*Wireless Setup''']] - 3G/4G Setup

[[ICV D8 Initial Configuration and Setup#Wifi Setup|'''*Wifi Setup''']] - Wifi Setup

[[ICV D8 Initial Configuration and Setup#Fuel|'''*Fuel''']] - 

[[ICV D8 Initial Configuration and Setup#Serial|'''*Serial''']] - Com Port setup

<br><br><br><br><br><br><br>

====PTZ Setup====

<br>

====Wireless Setup====

[[File:icvd8_4g_setup.jpg|left|350px|]]

<br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br>

====Wifi Setup====

<br>

====Fuel====

<br>

====Serial====

<br>

===Search Settings===

[[File:icvd8_search_menu.jpg|left|350px|]]

<br><br><br><br><br><br><br><br><br><br><br><br><br>

===System Info===

[[File:icvd8_system_info.jpg|left|350px|]]

<br><br><br><br><br><br><br><br><br><br><br><br><br>

=Configure=

==Firmware upgrade with USB Stick==

1.Device must switch off power disconnect the power source before upgrading;
 
2.Extract the rar file,  copy the .crc file to a USB flash memory FAT32 format, insert the flash memory to the MDVR USB port.

3.Power on the MDVR(connect the power), it will update automatically once the MDVR starts up. and the monitor will display "upgrading..."
 
4.Device will automatically restart when the upgrade is complete. 

Attention: Upgrade will need about 3-5 minutes. Make sure power connecting all the time during upgrading

<br><br>

===Firmware upgrade with SD Card===

1.Device must switch off power;
  
2.Decompress the rar file,  copy the .crc file to a SD card, and insert the SD card to the MDVR SD card port.

3.Power on the MDVR, it will update automatically once the MDVR starts up. and the monitor will display "upgrading..."
 
4.Device will automatically restart when the upgrade is complete. 

Note: upgrade will need about 3 minutes. Make sure power connecting all the time during upgrading.

<br><br>