Idrive - User contributions [en]

New D4M (4/17/19) Initial Configuration and Setup

2019-05-06T18:15:08Z

Brian: /* Main Menu */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[File:SSDinD4.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

[[File:HDMIvsCVBS.JPG|right|450px]]

::1)*Plug in a Mouse into the USB port on the left hand side of the Front Panel (no Remote Control with the D4M)

 
<div style="text-align: right; direction: ltr; margin-left: 1em;">When plugging in Monitor you can use the provided Composite Video (NTSC output) and connect to the USB Video capture device using AMCAP... or if your monitor has an open HDMI input the image will be full screen and the Mouse will be easier to point on a large Desktop 21" Monitor </div>

 

::In the Rear Panel>

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]
 

::1)*Confirm that the Alarm Wire SNR1 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

[[File:Settings.AlarmSetting.JPG|right]]

'''NOTE: this will only function after the CFG is loaded to the D4M'''

see pic on right after cfg is loaded

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

'''*Download the Latest Config File''' [[media:Hidvr.zip|hidvr.zip]]

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

'''Note: if the SD has been used in another Deck it might have 2 additional files... if so only select the Hidvr.cfg'''
[[File:SD CFG.JPG]]

* Main Menu> System> Config Operation>
:'''Import Configuration Browse and select file "hidvr.cfg" and click OK'''

'''Note: this will only take a second and may or may not appear to change the screen, but it is finished.'''

Hit return on the bottom to return to the previous menu

[[File:System.Config.Import.SD.hidvr.cfg.jpg]]
 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID”

:'''Menu> Mobile> Motor> License ID'''

[[File:Mobile.MotorSetting.JPG ]]

*Set the Customer's Time Zone
: '''Menu> Setting> Date/Time> Timezone'''
*Set the Customer's Time

: '''Menu> Setting> Date/Time> Set Time'''
*Set the Customer's Daylight Savings Time

: Menu> '''Setting> DST Setting> USA'''

::'''Note''' Selecting USA sets DST Correctly

[[File:Settings.Date.Time.JPG ]]

'''IMPORTANT! Click on APPLY before leaving screen or restarting'''

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Server related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (40)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:Record.RecordDetails.JPG|left|400px|]]

::1)* Resolution - '''DEFAULT(BASIC,2/3D1)'''
::2)* Bitrate(Kbps) - '''DEFAULT(200)'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''5 (Set 5 on all 4 Channels)'''
::6)* Record with Audio - '''YES (Set YES on all 4 Channels)'''
::7)* Record Mode - '''DEFAULT(AUTO)'''
::8)* Size(MBytes/hour) - '''DEFAULT(710)'''
::9)* Camera Status - '''DEFAULT (Monitored,OK)'''
::10)* Record Status - '''DEFAULT (Monitored,Recording)'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''CFG sets to 60 seconds (ON)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:Mobile.PowerSetting.JPG|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAULT(High)'''
::2)* ACC Power Off Delay(seconds)) - '''CFG set to 1 Second'''
::3)* Sleep Delay-ACC Off(seconds) - '''CFG set to 0'''
::4)* Sleep Delay-No Alarm(seconds) - '''CFG set to 0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3 (monitored)'''
::8)* Power Off Threshold Voltage - '''Set to 8VDC'''
::9)* Power On threshold Voltage - '''Set to 9VDC'''

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT(Monitored, Not Found)'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT(Monitored)'''
::2)* Initial Offset - '''DEFAULT(0,0,-1 TBD)'''
::3)* Alarm Threshold - '''DEFAULT(0,0,0 TBD)'''
::4)* Alarm Buzzer - '''DEFAULT(TBD)'''
::5)* Alarm Record - '''DEFAULT(TBD)'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT(Monitored,Module Not Found) '''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT(Blank)'''
::5)* Username - '''DEFAULT(Blank)'''
::6)* Password - '''DEFAULT(Blank)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Monitored, Module not found'''
::4)* WiFi IP - '''DEFAULT(Blank)'''
::5)* SSID - '''DEFAULT(Blank)'''
::6)* WiFi List - '''DEFAULT(Blank)'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''
::10)* IP - '''DEFAULT(192.168.33.1 TBD)'''
::11)* AP SSID - '''DEFAULT(HDVR, TBD)'''
::12)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(Monitored, Disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Monitored,Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enable(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:Settings.AlarmSetting.JPG|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS NTSC'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-05-06T17:17:32Z

Brian: /* Install Hard Drive/SSD */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:SSDinD4A.png|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

[[File:HDMIvsCVBS.JPG|right|450px]]

::1)*Plug in a Mouse into the USB port on the left hand side of the Front Panel (no Remote Control with the D4M)

 
<div style="text-align: right; direction: ltr; margin-left: 1em;">When plugging in Monitor you can use the provided Composite Video(NTSC output)and connect to the USB Video capture device using AMCAP... or if your monitor has an open HDMI input the image will be full screen and the Mouse will be easier to point on a large Desktop 21" Monitor </div>

 

::In the Rear Panel>

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]
 

::1)*Confirm that the Alarm Wire SNR1 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

[[File:Settings.AlarmSetting.JPG|right]]

'''NOTE: this will only function after the CFG is loaded to the D4M'''

see pic on right after cfg is loaded

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

'''*Download the Latest Config File''' [[media:Hidvr.zip|hidvr.zip]]

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

'''Note: if the SD has been used in another Deck it might have 2 additional files... if so only select the Hidvr.cfg'''
[[File:SD CFG.JPG]]

* Main Menu> System> Config Operation>
:'''Import Configuration Browse and select file "hidvr.cfg" and click OK'''

'''Note: this will only take a second and may or may not appear to change the screen, but it is finished.'''

Hit return on the bottom to return to the previous menu

[[File:System.Config.Import.SD.hidvr.cfg.jpg]]
 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID”

:'''Menu> Mobile> Motor> License ID'''

[[File:Mobile.MotorSetting.JPG ]]

*Set the Customer's Time Zone
: '''Menu> Setting> Date/Time> Timezone'''
*Set the Customer's Time

: '''Menu> Setting> Date/Time> Set Time'''
*Set the Customer's Daylight Savings Time

: Menu> '''Setting> DST Setting> USA'''

::'''Note''' Selecting USA sets DST Correctly

[[File:Settings.Date.Time.JPG ]]

'''IMPORTANT! Click on APPLY before leaving screen or restarting'''

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (40)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT(BASIC,2/3D1)'''
::2)* Bitrate(Kbps) - '''DEFAULT(200)'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''5'''
::6)* Record with Audio - '''DEFAULT(NO,ALL)'''
::7)* Record Mode - '''DEFAULT(AUTO)'''
::8)* Size(MBytes/hour) - '''DEFAULT(710)'''
::9)* Camera Status - '''DEFAULT(Monitored,OK)'''
::10)* Record Status - '''DEFAULT(Monitored,Recording)'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''CFG sets to 60 seconds (ON)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:Mobile.PowerSetting.JPG|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAULT(High)'''
::2)* ACC Power Off Delay(seconds)) - '''CFG set to 1 Second'''
::3)* Sleep Delay-ACC Off(seconds) - '''CFG set to 0'''
::4)* Sleep Delay-No Alarm(seconds) - '''CFG set to 0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3 (monitored)'''
::8)* Power Off Threshold Voltage - '''Set to 8VDC'''
::9)* Power On threshold Voltage - '''Set to 9VDC'''

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT(Monitored, Not Found)'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT(Monitored)'''
::2)* Initial Offset - '''DEFAULT(0,0,-1 TBD)'''
::3)* Alarm Threshold - '''DEFAULT(0,0,0 TBD)'''
::4)* Alarm Buzzer - '''DEFAULT(TBD)'''
::5)* Alarm Record - '''DEFAULT(TBD)'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT(Monitored,Module Not Found) '''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT(Blank)'''
::5)* Username - '''DEFAULT(Blank)'''
::6)* Password - '''DEFAULT(Blank)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Monitored, Module not found'''
::4)* WiFi IP - '''DEFAULT(Blank)'''
::5)* SSID - '''DEFAULT(Blank)'''
::6)* WiFi List - '''DEFAULT(Blank)'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''
::10)* IP - '''DEFAULT(192.168.33.1 TBD)'''
::11)* AP SSID - '''DEFAULT(HDVR, TBD)'''
::12)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(Monitored, Disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Monitored,Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enable(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS NTSC'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

File:D4M Hard Drive Inst.jpg

2019-05-06T17:11:41Z

Brian: Brian uploaded a new version of "File:D4M Hard Drive Inst.jpg"

New D4M (4/17/19) Initial Configuration and Setup

2019-05-01T23:08:09Z

Brian: /* Setting */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse into the USB port on the left hand side of the Front Panel(no Remote Control with the D4M)

 

::In the Rear Panel>

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm that the Alarm Wire SNR1 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (40)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT(BASIC,2/3D1)'''
::2)* Bitrate(Kbps) - '''DEFAULT(200)'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''5'''
::6)* Record with Audio - '''DEFAULT(NO,ALL)'''
::7)* Record Mode - '''DEFAULT(AUTO)'''
::8)* Size(MBytes/hour) - '''DEFAULT(710)'''
::9)* Camera Status - '''DEFAULT(Monitored,OK)'''
::10)* Record Status - '''DEFAULT(Monitored,Recording)'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAULT(High)'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30,TBD)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60,TBD)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''DEFAULT(Effect TBD,12.8)'''
::9)* Power On threshold Voltage - '''DEFAULT(Effect TBD,13.1)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT(Monitored, Not Found)'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT(Monitored)'''
::2)* Initial Offset - '''DEFAULT(0,0,-1 TBD)'''
::3)* Alarm Threshold - '''DEFAULT(0,0,0 TBD)'''
::4)* Alarm Buzzer - '''DEFAULT(TBD)'''
::5)* Alarm Record - '''DEFAULT(TBD)'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT(Monitored,Module Not Found) '''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT(Blank)'''
::5)* Username - '''DEFAULT(Blank)'''
::6)* Password - '''DEFAULT(Blank)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Monitored, Module not found'''
::4)* WiFi IP - '''DEFAULT(Blank)'''
::5)* SSID - '''DEFAULT(Blank)'''
::6)* WiFi List - '''DEFAULT(Blank)'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''
::10)* IP - '''DEFAULT(192.168.33.1 TBD)'''
::11)* AP SSID - '''DEFAULT(HDVR, TBD)'''
::12)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(Monitored, Disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Monitored,Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enable(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-05-01T20:38:39Z

Brian: /* Setting */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse into the USB port on the left hand side of the Front Panel(no Remote Control with the D4M)

 

::In the Rear Panel>

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm that the Alarm Wire SNR1 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (40)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT(BASIC,2/3D1)'''
::2)* Bitrate(Kbps) - '''DEFAULT(200)'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''5'''
::6)* Record with Audio - '''DEFAULT(NO,ALL)'''
::7)* Record Mode - '''DEFAULT(AUTO)'''
::8)* Size(MBytes/hour) - '''DEFAULT(710)'''
::9)* Camera Status - '''DEFAULT(Monitored,OK)'''
::10)* Record Status - '''DEFAULT(Monitored,Recording)'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAULT(High)'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30,TBD)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60,TBD)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''DEFAULT(Effect TBD,12.8)'''
::9)* Power On threshold Voltage - '''DEFAULT(Effect TBD,13.1)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT(Monitored, Not Found)'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT(Monitored)'''
::2)* Initial Offset - '''DEFAULT(0,0,-1 TBD)'''
::3)* Alarm Threshold - '''DEFAULT(0,0,0 TBD)'''
::4)* Alarm Buzzer - '''DEFAULT(TBD)'''
::5)* Alarm Record - '''DEFAULT(TBD)'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT(Monitored,Module Not Found) '''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT(Blank)'''
::5)* Username - '''DEFAULT(Blank)'''
::6)* Password - '''DEFAULT(Blank)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Monitored, Module not found'''
::4)* WiFi IP - '''DEFAULT(Blank)'''
::5)* SSID - '''DEFAULT(Blank)'''
::6)* WiFi List - '''DEFAULT(Blank)'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''
::10)* IP - '''DEFAULT(192.168.33.1 TBD)'''
::11)* AP SSID - '''DEFAULT(HDVR, TBD)'''
::12)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(Monitored, Disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Monitored,Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enable(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-05-01T19:48:17Z

Brian: /* Network */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse into the USB port on the left hand side of the Front Panel(no Remote Control with the D4M)

 

::In the Rear Panel>

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm that the Alarm Wire SNR1 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (40)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT(BASIC,2/3D1)'''
::2)* Bitrate(Kbps) - '''DEFAULT(200)'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''5'''
::6)* Record with Audio - '''DEFAULT(NO,ALL)'''
::7)* Record Mode - '''DEFAULT(AUTO)'''
::8)* Size(MBytes/hour) - '''DEFAULT(710)'''
::9)* Camera Status - '''DEFAULT(Monitored,OK)'''
::10)* Record Status - '''DEFAULT(Monitored,Recording)'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAULT(High)'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30,TBD)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60,TBD)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''DEFAULT(Effect TBD,12.8)'''
::9)* Power On threshold Voltage - '''DEFAULT(Effect TBD,13.1)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT(Monitored, Not Found)'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT(Monitored)'''
::2)* Initial Offset - '''DEFAULT(0,0,-1 TBD)'''
::3)* Alarm Threshold - '''DEFAULT(0,0,0 TBD)'''
::4)* Alarm Buzzer - '''DEFAULT(TBD)'''
::5)* Alarm Record - '''DEFAULT(TBD)'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT(Monitored,Module Not Found) '''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT(Blank)'''
::5)* Username - '''DEFAULT(Blank)'''
::6)* Password - '''DEFAULT(Blank)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Monitored, Module not found'''
::4)* WiFi IP - '''DEFAULT(Blank)'''
::5)* SSID - '''DEFAULT(Blank)'''
::6)* WiFi List - '''DEFAULT(Blank)'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''
::10)* IP - '''DEFAULT(192.168.33.1 TBD)'''
::11)* AP SSID - '''DEFAULT(HDVR, TBD)'''
::12)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(Monitored, Disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Monitored,Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-05-01T19:45:10Z

Brian: /* Network */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse into the USB port on the left hand side of the Front Panel(no Remote Control with the D4M)

 

::In the Rear Panel>

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm that the Alarm Wire SNR1 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (40)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT(BASIC,2/3D1)'''
::2)* Bitrate(Kbps) - '''DEFAULT(200)'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''5'''
::6)* Record with Audio - '''DEFAULT(NO,ALL)'''
::7)* Record Mode - '''DEFAULT(AUTO)'''
::8)* Size(MBytes/hour) - '''DEFAULT(710)'''
::9)* Camera Status - '''DEFAULT(Monitored,OK)'''
::10)* Record Status - '''DEFAULT(Monitored,Recording)'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAULT(High)'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30,TBD)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60,TBD)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''DEFAULT(Effect TBD,12.8)'''
::9)* Power On threshold Voltage - '''DEFAULT(Effect TBD,13.1)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT(Monitored, Not Found)'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT(Monitored)'''
::2)* Initial Offset - '''DEFAULT(0,0,-1 TBD)'''
::3)* Alarm Threshold - '''DEFAULT(0,0,0 TBD)'''
::4)* Alarm Buzzer - '''DEFAULT(TBD)'''
::5)* Alarm Record - '''DEFAULT(TBD)'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT(Monitored,Module Not Found) '''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT(Blank)'''
::5)* Username - '''DEFAULT(Blank)'''
::6)* Password - '''DEFAULT(Blank)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Monitored, Module not found'''
::4)* WiFi IP - '''DEFAULT(Blank)'''
::5)* SSID - '''DEFAULT(Blank)'''
::6)* WiFi List - '''DEFAULT(Blank)'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''
::10)* IP - '''DEFAULT(192.168.33.1 TBD)'''
::11)* AP SSID - '''DEFAULT(HDVR, TBD)'''
::12)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(Monitored, Disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Monitored,Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-05-01T19:41:48Z

Brian: /* Network */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse into the USB port on the left hand side of the Front Panel(no Remote Control with the D4M)

 

::In the Rear Panel>

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm that the Alarm Wire SNR1 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (40)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT(BASIC,2/3D1)'''
::2)* Bitrate(Kbps) - '''DEFAULT(200)'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''5'''
::6)* Record with Audio - '''DEFAULT(NO,ALL)'''
::7)* Record Mode - '''DEFAULT(AUTO)'''
::8)* Size(MBytes/hour) - '''DEFAULT(710)'''
::9)* Camera Status - '''DEFAULT(Monitored,OK)'''
::10)* Record Status - '''DEFAULT(Monitored,Recording)'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAULT(High)'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30,TBD)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60,TBD)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''DEFAULT(Effect TBD,12.8)'''
::9)* Power On threshold Voltage - '''DEFAULT(Effect TBD,13.1)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT(Monitored, Not Found)'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT(Monitored)'''
::2)* Initial Offset - '''DEFAULT(0,0,-1 TBD)'''
::3)* Alarm Threshold - '''DEFAULT(0,0,0 TBD)'''
::4)* Alarm Buzzer - '''DEFAULT(TBD)'''
::5)* Alarm Record - '''DEFAULT(TBD)'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT(Monitored,Module Not Found) '''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT(Blank)'''
::5)* Username - '''DEFAULT(Blank)'''
::6)* Password - '''DEFAULT(Blank)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Monitored, Module not found'''
::4)* WiFi IP - '''DEFAULT(Blank)'''
::5)* SSID - '''DEFAULT(Blank)'''
::6)* WiFi List - '''DEFAULT(Blank)'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''
::10)* IP - '''DEFAULT(192.168.33.1 TBD)'''
::11)* AP SSID - '''DEFAULT(HDVR, TBD)'''
::12)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(Monitored, Disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-05-01T19:32:27Z

Brian: /* Network */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse into the USB port on the left hand side of the Front Panel(no Remote Control with the D4M)

 

::In the Rear Panel>

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm that the Alarm Wire SNR1 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (40)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT(BASIC,2/3D1)'''
::2)* Bitrate(Kbps) - '''DEFAULT(200)'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''5'''
::6)* Record with Audio - '''DEFAULT(NO,ALL)'''
::7)* Record Mode - '''DEFAULT(AUTO)'''
::8)* Size(MBytes/hour) - '''DEFAULT(710)'''
::9)* Camera Status - '''DEFAULT(Monitored,OK)'''
::10)* Record Status - '''DEFAULT(Monitored,Recording)'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAULT(High)'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30,TBD)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60,TBD)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''DEFAULT(Effect TBD,12.8)'''
::9)* Power On threshold Voltage - '''DEFAULT(Effect TBD,13.1)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT(Monitored, Not Found)'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT(Monitored)'''
::2)* Initial Offset - '''DEFAULT(0,0,-1 TBD)'''
::3)* Alarm Threshold - '''DEFAULT(0,0,0 TBD)'''
::4)* Alarm Buzzer - '''DEFAULT(TBD)'''
::5)* Alarm Record - '''DEFAULT(TBD)'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT(Monitored,Module Not Found) '''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT(Blank)'''
::5)* Username - '''DEFAULT(Blank)'''
::6)* Password - '''DEFAULT(Blank)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Monitored, Module not found'''
::4)* WiFi IP - '''DEFAULT(Blank)'''
::5)* SSID - '''DEFAULT(Blank)'''
::6)* WiFi List - '''DEFAULT(Blank)'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''
::10)* IP - '''DEFAULT(192.168.33.1 TBD)'''
::11)* AP SSID - '''DEFAULT(HDVR, TBD)'''
::12)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-05-01T18:55:41Z

Brian: /* G-Sensor */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse into the USB port on the left hand side of the Front Panel(no Remote Control with the D4M)

 

::In the Rear Panel>

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm that the Alarm Wire SNR1 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (40)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT(BASIC,2/3D1)'''
::2)* Bitrate(Kbps) - '''DEFAULT(200)'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''5'''
::6)* Record with Audio - '''DEFAULT(NO,ALL)'''
::7)* Record Mode - '''DEFAULT(AUTO)'''
::8)* Size(MBytes/hour) - '''DEFAULT(710)'''
::9)* Camera Status - '''DEFAULT(Monitored,OK)'''
::10)* Record Status - '''DEFAULT(Monitored,Recording)'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAULT(High)'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30,TBD)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60,TBD)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''DEFAULT(Effect TBD,12.8)'''
::9)* Power On threshold Voltage - '''DEFAULT(Effect TBD,13.1)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT(Monitored, Not Found)'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT(Monitored)'''
::2)* Initial Offset - '''DEFAULT(0,0,-1 TBD)'''
::3)* Alarm Threshold - '''DEFAULT(0,0,0 TBD)'''
::4)* Alarm Buzzer - '''DEFAULT(TBD)'''
::5)* Alarm Record - '''DEFAULT(TBD)'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-05-01T18:42:41Z

Brian: /* GPS */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse into the USB port on the left hand side of the Front Panel(no Remote Control with the D4M)

 

::In the Rear Panel>

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm that the Alarm Wire SNR1 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (40)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT(BASIC,2/3D1)'''
::2)* Bitrate(Kbps) - '''DEFAULT(200)'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''5'''
::6)* Record with Audio - '''DEFAULT(NO,ALL)'''
::7)* Record Mode - '''DEFAULT(AUTO)'''
::8)* Size(MBytes/hour) - '''DEFAULT(710)'''
::9)* Camera Status - '''DEFAULT(Monitored,OK)'''
::10)* Record Status - '''DEFAULT(Monitored,Recording)'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAULT(High)'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30,TBD)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60,TBD)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''DEFAULT(Effect TBD,12.8)'''
::9)* Power On threshold Voltage - '''DEFAULT(Effect TBD,13.1)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT(Monitored, Not Found)'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-05-01T18:29:52Z

Brian: /* Power */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse into the USB port on the left hand side of the Front Panel(no Remote Control with the D4M)

 

::In the Rear Panel>

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm that the Alarm Wire SNR1 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (40)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT(BASIC,2/3D1)'''
::2)* Bitrate(Kbps) - '''DEFAULT(200)'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''5'''
::6)* Record with Audio - '''DEFAULT(NO,ALL)'''
::7)* Record Mode - '''DEFAULT(AUTO)'''
::8)* Size(MBytes/hour) - '''DEFAULT(710)'''
::9)* Camera Status - '''DEFAULT(Monitored,OK)'''
::10)* Record Status - '''DEFAULT(Monitored,Recording)'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAULT(High)'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30,TBD)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60,TBD)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''DEFAULT(Effect TBD,12.8)'''
::9)* Power On threshold Voltage - '''DEFAULT(Effect TBD,13.1)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-05-01T18:20:44Z

Brian: /* Power */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse into the USB port on the left hand side of the Front Panel(no Remote Control with the D4M)

 

::In the Rear Panel>

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm that the Alarm Wire SNR1 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (40)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT(BASIC,2/3D1)'''
::2)* Bitrate(Kbps) - '''DEFAULT(200)'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''5'''
::6)* Record with Audio - '''DEFAULT(NO,ALL)'''
::7)* Record Mode - '''DEFAULT(AUTO)'''
::8)* Size(MBytes/hour) - '''DEFAULT(710)'''
::9)* Camera Status - '''DEFAULT(Monitored,OK)'''
::10)* Record Status - '''DEFAULT(Monitored,Recording)'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAULT(High)'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-05-01T18:15:38Z

Brian: /* Record */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse into the USB port on the left hand side of the Front Panel(no Remote Control with the D4M)

 

::In the Rear Panel>

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm that the Alarm Wire SNR1 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (40)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT(BASIC,2/3D1)'''
::2)* Bitrate(Kbps) - '''DEFAULT(200)'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''5'''
::6)* Record with Audio - '''DEFAULT(NO,ALL)'''
::7)* Record Mode - '''DEFAULT(AUTO)'''
::8)* Size(MBytes/hour) - '''DEFAULT(710)'''
::9)* Camera Status - '''DEFAULT(Monitored,OK)'''
::10)* Record Status - '''DEFAULT(Monitored,Recording)'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-05-01T18:12:49Z

Brian: /* Record */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse into the USB port on the left hand side of the Front Panel(no Remote Control with the D4M)

 

::In the Rear Panel>

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm that the Alarm Wire SNR1 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (40)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT(BASIC,2/3D1)'''
::2)* Bitrate(Kbps) - '''DEFAULT(200)'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''5'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT(AUTO)'''
::8)* Size(MBytes/hour) - '''DEFAULT(710)'''
::9)* Camera Status - '''DEFAULT(Monitored,OK)'''
::10)* Record Status - '''DEFAULT(Monitored,Recording)'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-05-01T18:10:53Z

Brian: /* Record */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse into the USB port on the left hand side of the Front Panel(no Remote Control with the D4M)

 

::In the Rear Panel>

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm that the Alarm Wire SNR1 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (40)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT(BASIC)'''
::2)* Bitrate(Kbps) - '''DEFAULT(200)'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''5'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT(AUTO)'''
::8)* Size(MBytes/hour) - '''DEFAULT(710)'''
::9)* Camera Status - '''DEFAULT(Monitored,OK)'''
::10)* Record Status - '''DEFAULT(Monitored,Recording)'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-05-01T17:31:08Z

Brian: /* Camera Settings */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse into the USB port on the left hand side of the Front Panel(no Remote Control with the D4M)

 

::In the Rear Panel>

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm that the Alarm Wire SNR1 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (40)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT'''
::2)* Bitrate(Kbps) - '''DEFAULT'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''?'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT'''
::8)* Size(MBytes/hour) - '''DEFAULT'''
::9)* Camera Status - '''DEFAULT'''
::10)* Record Status - '''DEFAULT'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-04-30T23:19:57Z

Brian: /* GPS */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse into the USB port on the left hand side of the Front Panel(no Remote Control with the D4M)

 

::In the Rear Panel>

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm that the Alarm Wire SNR1 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (50)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT'''
::2)* Bitrate(Kbps) - '''DEFAULT'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''?'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT'''
::8)* Size(MBytes/hour) - '''DEFAULT'''
::9)* Camera Status - '''DEFAULT'''
::10)* Record Status - '''DEFAULT'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-04-30T23:19:22Z

Brian: /* G-Sensor */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse into the USB port on the left hand side of the Front Panel(no Remote Control with the D4M)

 

::In the Rear Panel>

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm that the Alarm Wire SNR1 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (50)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT'''
::2)* Bitrate(Kbps) - '''DEFAULT'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''?'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT'''
::8)* Size(MBytes/hour) - '''DEFAULT'''
::9)* Camera Status - '''DEFAULT'''
::10)* Record Status - '''DEFAULT'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-04-30T23:18:30Z

Brian: /* GPS */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse into the USB port on the left hand side of the Front Panel(no Remote Control with the D4M)

 

::In the Rear Panel>

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm that the Alarm Wire SNR1 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (50)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT'''
::2)* Bitrate(Kbps) - '''DEFAULT'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''?'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT'''
::8)* Size(MBytes/hour) - '''DEFAULT'''
::9)* Camera Status - '''DEFAULT'''
::10)* Record Status - '''DEFAULT'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-04-30T23:17:35Z

Brian: /* GPS */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse into the USB port on the left hand side of the Front Panel(no Remote Control with the D4M)

 

::In the Rear Panel>

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm that the Alarm Wire SNR1 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (50)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT'''
::2)* Bitrate(Kbps) - '''DEFAULT'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''?'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT'''
::8)* Size(MBytes/hour) - '''DEFAULT'''
::9)* Camera Status - '''DEFAULT'''
::10)* Record Status - '''DEFAULT'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-04-30T23:16:33Z

Brian: /* GPS */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse into the USB port on the left hand side of the Front Panel(no Remote Control with the D4M)

 

::In the Rear Panel>

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm that the Alarm Wire SNR1 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (50)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT'''
::2)* Bitrate(Kbps) - '''DEFAULT'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''?'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT'''
::8)* Size(MBytes/hour) - '''DEFAULT'''
::9)* Camera Status - '''DEFAULT'''
::10)* Record Status - '''DEFAULT'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-04-30T22:59:00Z

Brian: /* Setup the D4 for configuration */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse into the USB port on the left hand side of the Front Panel(no Remote Control with the D4M)

 

::In the Rear Panel>

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm that the Alarm Wire SNR1 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (50)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT'''
::2)* Bitrate(Kbps) - '''DEFAULT'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''?'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT'''
::8)* Size(MBytes/hour) - '''DEFAULT'''
::9)* Camera Status - '''DEFAULT'''
::10)* Record Status - '''DEFAULT'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-04-30T22:52:34Z

Brian: /* Setup the D4 for configuration */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse into the USB port on the left hand side of the Front Panel(no Remote Control with the D4M)

 

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm the Alarm Wire A01 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (50)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT'''
::2)* Bitrate(Kbps) - '''DEFAULT'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''?'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT'''
::8)* Size(MBytes/hour) - '''DEFAULT'''
::9)* Camera Status - '''DEFAULT'''
::10)* Record Status - '''DEFAULT'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-04-30T22:41:22Z

Brian: /* Network */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse (no Remote Control with the D4M)

 

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm the Alarm Wire A01 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (50)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT'''
::2)* Bitrate(Kbps) - '''DEFAULT'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''?'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT'''
::8)* Size(MBytes/hour) - '''DEFAULT'''
::9)* Camera Status - '''DEFAULT'''
::10)* Record Status - '''DEFAULT'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-04-30T22:40:20Z

Brian: /* Network */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse (no Remote Control with the D4M)

 

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm the Alarm Wire A01 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (50)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT'''
::2)* Bitrate(Kbps) - '''DEFAULT'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''?'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT'''
::8)* Size(MBytes/hour) - '''DEFAULT'''
::9)* Camera Status - '''DEFAULT'''
::10)* Record Status - '''DEFAULT'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-04-30T22:39:26Z

Brian: /* G-Sensor */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse (no Remote Control with the D4M)

 

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm the Alarm Wire A01 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (50)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT'''
::2)* Bitrate(Kbps) - '''DEFAULT'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''?'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT'''
::8)* Size(MBytes/hour) - '''DEFAULT'''
::9)* Camera Status - '''DEFAULT'''
::10)* Record Status - '''DEFAULT'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-04-30T22:27:48Z

Brian: /* Setup the D4 for configuration */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse (no Remote Control with the D4M)

 

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm the Alarm Wire A01 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (50)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT'''
::2)* Bitrate(Kbps) - '''DEFAULT'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''?'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT'''
::8)* Size(MBytes/hour) - '''DEFAULT'''
::9)* Camera Status - '''DEFAULT'''
::10)* Record Status - '''DEFAULT'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

File:Legend5.png

2019-04-30T22:26:14Z

Brian:

New D4M (4/17/19) Initial Configuration and Setup

2019-04-30T22:25:27Z

Brian: /* Setup the D4 for configuration */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend2.png|left|300px|]]

[[file:legend5.png|left|300px|]]

 

::1)*Plug in a Mouse (no Remote Control with the D4M)

 

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm the Alarm Wire A01 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (50)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT'''
::2)* Bitrate(Kbps) - '''DEFAULT'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''?'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT'''
::8)* Size(MBytes/hour) - '''DEFAULT'''
::9)* Camera Status - '''DEFAULT'''
::10)* Record Status - '''DEFAULT'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-04-30T20:44:07Z

Brian: /* System */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend2.png|left|300px|]]

 

::1)*Plug in a Mouse (no Remote Control with the D4M)

 

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm the Alarm Wire A01 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (50)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT'''
::2)* Bitrate(Kbps) - '''DEFAULT'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''?'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT'''
::8)* Size(MBytes/hour) - '''DEFAULT'''
::9)* Camera Status - '''DEFAULT'''
::10)* Record Status - '''DEFAULT'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-04-30T20:41:37Z

Brian: /* System */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend2.png|left|300px|]]

 

::1)*Plug in a Mouse (no Remote Control with the D4M)

 

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm the Alarm Wire A01 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (50)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT'''
::2)* Bitrate(Kbps) - '''DEFAULT'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''?'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT'''
::8)* Size(MBytes/hour) - '''DEFAULT'''
::9)* Camera Status - '''DEFAULT'''
::10)* Record Status - '''DEFAULT'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?)'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

File:Legend2.png

2019-04-30T19:58:47Z

Brian:

New D4M (4/17/19) Initial Configuration and Setup

2019-04-30T19:53:25Z

Brian: /* Setup the D4 for configuration */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:legend2.png|left|300px|]]

 

::1)*Plug in a Mouse (no Remote Control with the D4M)

 

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm the Alarm Wire A01 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (50)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT'''
::2)* Bitrate(Kbps) - '''DEFAULT'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''?'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT'''
::8)* Size(MBytes/hour) - '''DEFAULT'''
::9)* Camera Status - '''DEFAULT'''
::10)* Record Status - '''DEFAULT'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?)'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

File:D4M Back Panel.png

2019-04-30T19:49:39Z

Brian: Brian uploaded a new version of "File:D4M Back Panel.png"

File:Alarmcble5.png

2019-04-30T18:17:01Z

Brian: Brian uploaded a new version of "File:Alarmcble5.png"

New D4M (4/17/19) Initial Configuration and Setup

2019-04-30T18:07:18Z

Brian: /* Setup the D4 for configuration */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:D4M_Back_Panel.png|left|300px|]]

 

::1)*Plug in a Mouse (no Remote Control with the D4M)

 

::1)*Plug in the Power Cable

::2)*Plug in the Monitor Cable

::3)*Plug in the Camera Cable

::4)*Turn power supply ON

::5)*Turn Key ON

::6)*Select Main Menu

 

[[file:Alarmcble5.png‎|left|px250]]

::1)*Confirm the Alarm Wire A01 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

 
 
 
 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (50)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT'''
::2)* Bitrate(Kbps) - '''DEFAULT'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''?'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT'''
::8)* Size(MBytes/hour) - '''DEFAULT'''
::9)* Camera Status - '''DEFAULT'''
::10)* Record Status - '''DEFAULT'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?)'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

File:Alarmcble5.png

2019-04-30T17:49:52Z

Brian: Brian uploaded a new version of "File:Alarmcble5.png"

New D4M (4/17/19) Initial Configuration and Setup

2019-04-30T17:47:50Z

Brian: /* Setup the D4 for configuration */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:D4M_Back_Panel.png|left|300px|]]

 

*Plug in a Mouse (no Remote Control with the D4M)

 

*Plug in the Power Cable

*Plug in the Monitor Cable

*Plug in the Camera Cable

*Turn power supply ON

*Turn Key ON

*Select Main Menu

 

*Confirm the Alarm Wire A01 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

[[file:Alarmcble5.png‎|left|px250]]

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (50)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT'''
::2)* Bitrate(Kbps) - '''DEFAULT'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''?'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT'''
::8)* Size(MBytes/hour) - '''DEFAULT'''
::9)* Camera Status - '''DEFAULT'''
::10)* Record Status - '''DEFAULT'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?)'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

File:Alarmcble5.png

2019-04-30T17:47:14Z

Brian: Brian uploaded a new version of "File:Alarmcble5.png"

File:Alarmcble5.png

2019-04-30T17:39:12Z

Brian:

New D4M (4/17/19) Initial Configuration and Setup

2019-04-30T17:38:50Z

Brian: /* Setup the D4 for configuration */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:D4M_Back_Panel.png|left|300px|]]

 

*Plug in a Mouse (no Remote Control with the D4M)

 

*Plug in the Power Cable

*Plug in the Monitor Cable

*Plug in the Camera Cable

*Turn power supply ON

*Turn Key ON

*Select Main Menu

 

*Confirm the Alarm Wire A01 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

[[file:Alarmcble5.png‎|px250]]

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (50)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT'''
::2)* Bitrate(Kbps) - '''DEFAULT'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''?'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT'''
::8)* Size(MBytes/hour) - '''DEFAULT'''
::9)* Camera Status - '''DEFAULT'''
::10)* Record Status - '''DEFAULT'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?)'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-04-30T17:27:48Z

Brian: /* Setup the D4 for configuration */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:D4M_Back_Panel.png|left|300px|]]

 

*Plug in a Mouse (no Remote Control with the D4M)

 

*Plug in the Power Cable

*Plug in the Monitor Cable

*Plug in the Camera Cable

*Turn power supply ON

*Turn Key ON

*Select Main Menu

 

*Confirm the Alarm Wire A01 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

[[file:Alarmcble2.png‎|px250]]

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (50)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT'''
::2)* Bitrate(Kbps) - '''DEFAULT'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''?'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT'''
::8)* Size(MBytes/hour) - '''DEFAULT'''
::9)* Camera Status - '''DEFAULT'''
::10)* Record Status - '''DEFAULT'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?)'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

File:Alarm Wires.png

2019-04-30T17:26:10Z

Brian:

New D4M (4/17/19) Initial Configuration and Setup

2019-04-30T17:24:38Z

Brian: /* Setup the D4 for configuration */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:D4M_Back_Panel.png|left|300px|]]

 

*Plug in a Mouse (no Remote Control with the D4M)

 

*Plug in the Power Cable

*Plug in the Monitor Cable

*Plug in the Camera Cable

*Turn power supply ON

*Turn Key ON

*Select Main Menu

 

*Confirm the Alarm Wire A01 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC

[[file:Alarm_Wires.png‎|px250]]

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (50)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT'''
::2)* Bitrate(Kbps) - '''DEFAULT'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''?'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT'''
::8)* Size(MBytes/hour) - '''DEFAULT'''
::9)* Camera Status - '''DEFAULT'''
::10)* Record Status - '''DEFAULT'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?)'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-04-30T17:19:11Z

Brian: /* Setup the D4 for configuration */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:D4M_Back_Panel.png|left|300px|]]

 

*Plug in a Mouse (no Remote Control with the D4M)

 

*Plug in the Power Cable

*Plug in the Monitor Cable

*Plug in the Camera Cable

*Turn power supply ON

*Turn Key ON

*Select Main Menu

 

*Confirm the Alarm Wire A01 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC
[[file:Alarm_Wires.png‎|px250]]

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (50)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT'''
::2)* Bitrate(Kbps) - '''DEFAULT'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''?'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT'''
::8)* Size(MBytes/hour) - '''DEFAULT'''
::9)* Camera Status - '''DEFAULT'''
::10)* Record Status - '''DEFAULT'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?)'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-04-30T17:01:48Z

Brian: /* Setup the D4 for configuration */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:D4M_Back_Panel.png|left|300px|]]

 

*Plug in a Mouse (no Remote Control with the D4M)

 

*Plug in the Power Cable

*Plug in the Monitor Cable

*Plug in the Camera Cable

*Turn power supply ON

*Turn Key ON

*Select Main Menu

 

*Confirm the Alarm Wire A01 (Grey wire below the purple wire on the black Molex plug) triggers Cam Ch#2 to full screen when connecting the Grey wire to 12VDC
[[file:Alarm_Wires.jpg‎|px250]]

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (50)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT'''
::2)* Bitrate(Kbps) - '''DEFAULT'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''?'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT'''
::8)* Size(MBytes/hour) - '''DEFAULT'''
::9)* Camera Status - '''DEFAULT'''
::10)* Record Status - '''DEFAULT'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?)'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-04-30T16:51:39Z

Brian: /* Setup the D4 for configuration */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:D4M_Back_Panel.png|left|300px|]]

 

*Plug in a Mouse (no Remote Control with the D4M)

 

*Plug in the Power Cable

*Plug in the Monitor Cable

*Plug in the Camera Cable

*Turn power supply ON

*Turn Key ON

*Select Main Menu

 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (50)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT'''
::2)* Bitrate(Kbps) - '''DEFAULT'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''?'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT'''
::8)* Size(MBytes/hour) - '''DEFAULT'''
::9)* Camera Status - '''DEFAULT'''
::10)* Record Status - '''DEFAULT'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?)'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

New D4M (4/17/19) Initial Configuration and Setup

2019-04-30T16:27:36Z

Brian: /* Setup the D4 for configuration */

=Idrive D4M Configuration=

 

==Record Serial Number==

[[file:D4M_Serial_Number.jpg‎|left|300px|]]

Serial number is located on the bottom of the D4M.

:Remove D4M from the Security Box

:Record Serial number

 

[[file:D4M_Serial_Label.jpg|left|300px|]]

:Print Label and afix to the top of the D4M

 

*Enter Serial Number into Admin Center.

::AC> Manufacturing >D4-DVR Production Tab

::Click on ADD and enter the S/N

::Select Item Type '''IDRDVRD4HD'''

 

==Install Hard Drive/SSD==

[[file:D4M_Hard_Drive_Inst.jpg|left|300px|]]

Use the 4 screws in the plastic bag with the keys to secure the SSD in the carriage

Install the Hard Drive Sled into the D4M

 

==Setup the D4 for configuration==

[[file:D4M_Front.png|left|300px|]]

[[file:D4M_Back_Panel.png|left|300px|]]

 

*Plug in a Mouse (no Remote Control with the D4M)

 

*Plug in the Power Cable

*Plug in the Monitor Cable

*Plug in the Camera Cable

*Turn power supply ON

*Turn Key ON

*Select Main Menu

 

===Click the Right Mouse Button For Options===

[[file:D4M_Right_Click.jpg|left|100px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''Main Menu''']] - DVR Configuration Options

::2)*SingleScreen - Display one Camera on the Monitor

::3)*MultiScreen - Display all 4 cameras on the monitor

::4)*UpScreen - Figure it out

::5)*DownScreen - Figure it out

::6)*Screen Save - Save the current screen configuration as Default

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Main Menu|'''PTZ''']]

 

==Verify Correct Firmware version==

 Main Menu> System> System Info

Current Release '''V206-2019/4/12-10:11:124'''

===Upgrade Firmware if needed===

*Obtain Latest Firmware Version from AdminCenter (if we receive one)

*Place the Firmware on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> System Upgrade> Browse and select file and click OK

[[file:D4M_FW_Update.jpg‎|left|300px|]]

 

==Import Idrive Default Configuration==

*Obtain Latest Config File from AdminCenter (if we receive one)

*Place the Config File on a SD Card (USB Port is in use for the mouse)

*Insert the SD card into the DVR

* Main Menu> System> Config Operation> Import Configuration Browse and select file and click OK

 

==Verify Config and customize Settings==

*Enter the serial number for the D4M into the “LICENSE ID” Menu> Mobile> Motor> License ID

*Set the CUSTOMER's Time Zone Menu> Setting> Date/Time> Timezone

*Set the CUSTOMER's Time Menu> Setting> Date/Time> Set Time

*Set the CUSTOMER's Daylight Savings Time Menu> Setting> Dst Setting> USA

::'''Note''' No need to fill in the week day or Hour. USA sets this

*Turn Key OFF

*Remove SD Card

==Format the SSD / Hard Drive==

* Install the hard drive carriage into the D4M

* Turn the key ON

* Format the SSD/Hard Drive Menu> Storage> Disk Info> Format

::The Format Button is at the bottom but does not display in AMCAP

* Push record and verify that it can write to the hard drive.

* Push stop

* Test all camera ports with a working camera to ensure that they all work.

* Turn the Key and Power supply off.

* Box up unit with serial number on the outside of the box

 

=Main Menu=

The Main Menu is Displayed by right clicking the USB mouse .

[[File:D4M_Main_Menu.jpg|left|300px|]]

::1)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Preview|'''*Preview''']] - Camera Setting, Motion Setting

::2)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*Record''']] - Video program, parameters and related configuration

::3)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Storage|'''*Storage''']] - Hard disk information and formatting

::4)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Mobile|'''*Mobile''']] - Power, motor, GPS, G-sensor etc.

::5)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Network|'''*Network''']] - 3G/4G, LAN, Sever related configuration

::6)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Setting|'''*Setting''']] - User, alarm system parameters, such as configuration

::7)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#Record|'''*File''']] - The captured image display and operation

::8)*[[New_D4M_(4/17/19)_Initial_Configuration_and_Setup#System|'''*System''']] - System info, upgrade management, etc.

 

==Preview==

===Camera Settings===

Each channel set separately

[[File:d4m_Camera_Setting.png|left|500px|]]

::1)*Video Lost Beep - Enable for beep when video is lost '''OFF'''

::2)* Camera Title - '''DEFAULT(CH:0#)?'''

::3)*AHD Camera Type - '''AUTO DETECT'''

::4)*Power Line Frequence - '''?'''

::5)*Frame Rate - '''DEFAULT (30)'''

::6)*FLIP - Mirror horizontal or vertical '''OFF,OFF'''

::7)*Brightness * '''DEFAULT (50)'''

::8)*Contrast - '''DEFAULT (40)'''

::9)*Hue - '''DEFAULT (50)'''

::10)*Saturation - '''DEFAULT (50)'''

::11)*Audio Volume - '''DEFAULT (50)'''

::12)*Auto Black-and-White - At night switch to Black and White mode '''OFF'''

::13)*FrameRate Down - lower frame rate at night '''OFF'''

::14)*IR LED Light - Only if supported by the camera '''AUTO'''

::15)*LED Status Indicator - '''OFF'''

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

===Motion Settings===

[[File:d4m_Motion_Setting.png|left|500px|]]

Each channel set separately

::1)*Motion Zone Settings '''All Clear'''

::2)* Enable Adaptive Bit rate '''Default'''

::3)* Record when motion detection triggered '''Default'''

::4)* Alarm Buzzer '''Default'''

::5)* Sensitivity(0-100) '''Default(50)'''

::6)* Percent of enabled area required to trigger (0-100) '''Default(10)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record==

[[File:D4M_Record_Details.png|left|400px|]]

::1)* Resolution - '''DEFAULT'''
::2)* Bitrate(Kbps) - '''DEFAULT'''
::3)* Frame Rate(1-30) - '''DEFAULT(30)'''
::4)* Real Frame Rate - '''30'''
::5)* File Length(Minutes) - '''?'''
::6)* Record with Audio - '''DEFAULT(NO)'''
::7)* Record Mode - '''DEFAULT'''
::8)* Size(MBytes/hour) - '''DEFAULT'''
::9)* Camera Status - '''DEFAULT'''
::10)* Record Status - '''DEFAULT'''
::11)* Stop All Stop - '''Do not press, unless intending to stop recording.'''
::12)* Record File Encryption - '''DEFAULT(Blank)'''

 

 '''Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Record Schedule==

[[File:D4M_Schedule_Setting.png|left|400px|]]

::1)* HH:MM HH:MM Leave this section blank - '''DEFAULT'''

 

 '''Clear, Copy To, Apply, Return Buttons''' not shown in AMCAP

 

==Storage==

[[File:D4M_Storage_Basesetting.png|left|400px|]]

::1)* Overwrite Mode - '''DEFAULT(Overwrite normal video)'''
::2)* No disk alarm time(seconds)) - '''DEFAULT(Off)'''
::3)* Normal Record Disk - '''DEFAULT(sata)'''
::4)* Alarm Record Disk - '''DEFAULT(sata)'''
::5)* Format - '''Use Format Only at Initialization of SSD'''

 

 '''Format, Refresh, Apply, Return Buttons''' not shown in AMCAP

 

==Mobile==

[[File:D4M_Mobile_Power.png|left|400px|]]

==Power==

[[File:D4M_Mobile_Motor.png|left|400px|]]

::1)* Ignition Level - '''DEFAUL(High)T'''
::2)* ACC Power Off Delay(seconds)) - '''DEFAULT(30)'''
::3)* Sleep Delay-ACC Off(seconds) - '''DEFAULT(60)'''
::4)* Sleep Delay-No Alarm(seconds) - '''0'''
::5)* Power On at(HH:MM) - '''00:00'''
::6)* Power Off at (HH:MM) - '''00:00'''
::7)* Current Voltage - '''13.3(monitored)'''
::8)* Power Off Threshold Voltage - '''12.9'''
::9)* Power On threshold Voltage - '''13.0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==Motor==

::1)* License ID - '''ENTER S/N'''
::2)* Obtain Speed - '''DEFAULT(From GPS(If any))'''
::3)* Speed Unit - '''MPH'''
::4)* Speed Limit - '''65'''
::5)* Overspeed Record - '''DEFAULT'''
::6)* Overspeed OSD - '''SPD'''
::7)* Overspeed buzzer - '''Off'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

 

==GPS==

[[File:D4M_Mobile_GPS.png|left|400px|]]

::1)* GPS Status - '''DEFAULT'''
::2)* GPS OSD - '''DEFAULT(On)'''
::3)* GPS Baudrate - '''DEFAULT(9600)'''
::4)* Sync with GPS time - '''Check'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==G-Sensor==

[[File:D4M_Mobile_G-Sensor.png|left|400px|]]

::1)* Instant Value - '''DEFAULT'''
::2)* Initial Offset - '''DEFAULT'''
::3)* Alarm Threshold - '''DEFAULT'''
::4)* Alarm Buzzer - '''DEFAULT'''
::5)* Alarm Record - '''DEFAULT'''

 

 ''' Correction, Refresh, Apply, Return Buttons''' not shown in AMCAP

 
 

==Network==

[[File:D4M_Network_3G_4G.png|left|400px|]]

::'''3G/4G'''

::1)* 3G/4G Status - '''DEFAULT'''
::2)* Dial Enable - '''DEFAULT(Check))'''
::3)* Dial Number - '''DEFAULT(Blank)'''
::4)* APN - '''DEFAULT'''
::5)* Username - '''DEFAULT'''
::6)* Password - '''DEFAULT'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Wifi.png|left|400px|]]

 

::'''WiFi'''

::1)* Enable - '''DEFAULT(Uncheck)'''
::2)* Mode - '''DEFAULT(Do not Select)'''
::3)* WiFi Status - '''Module not found'''
::4)* WiFi IP - '''DEFAULT'''
::5)* SSID - '''DEFAULT'''
::6)* WiFi List - '''SPD'''
::7)* AP Scan - '''DEFAULT'''
::8)* Signal Strength - '''DEFAULT'''
::9)* Password - '''DEFAULT'''

 ''' Apply, Refresh, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_LAN.png|left|400px|]]

 

::'''LAN'''

::1)* DHCP - '''DEFAULT(Uncheck)'''
::2)* IP - '''DEFAULT(192.168.0.220)'''
::3)* Subnet Mask Status - '''DEFAULT(255.255.255.0)'''
::4)* Default Gateway - '''DEFAULT(192.168.0.1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_Server_Settings.png|left|400px|]]

 

::'''Server Settings'''

::1)* Server Status - '''DEFAULT(disconnected)'''
::2)* Client DVR ID - '''DEFAULT(S/N)'''
::3)* Server - '''DEFAULT(192.168.0.128)'''
::4)* Server Port - '''DEFAULT(10000)'''
::5)* Channel - '''DEFAULT(1)'''
::6)* Resolution - '''DEFAULT(640x360)'''
::7)* Bitrate(Kbps) - '''DEFAULT(100)'''
::8)* Framerate(1-30) - '''DEFAULT(10)'''
::9)* Talkback Channel- '''DEFAULT(1)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Network_GPS_Server_Settings.png|left|400px|]]

 

::'''GPS Server Settings'''

::1)* GPS Network ID - '''DEFAULT(S/N)'''
::2)* GPS Server IP - '''DEFAULT)'''
::3)* GPS Server Port - '''DEFAULT(0)'''
::4)* GPS Server Status - '''DEFAULT(Disconnected)'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 
 

==Setting==

[[File:D4M_Setting_Common_Setting.png|left|400px|]]

::'''Basic Settings'''

::1)* Toolbartip Bar Show - '''Enabe(Check)'''
::2)* DVR Time Display - '''Enable(Check)'''
::3)* USB Auto Update - '''DEFAULT(Not checked)'''
::4)* Language Mode - '''English'''
::5)* GUI Skin - '''Black'''
::6)* Transparent - '''Translucent'''
::7)* AHD Camera Num - '''4'''

 ''' Apply, Return Buttons''' not shown in AMCAP

 

[[File:D4M_Setting_Alarm_Setting.png|left|400px|]]

:: '''Alarm Settings'''

::1)* Alarm - '''Sensor1 1'''
::2)* Trigger Level/Mode - '''High'''
::3)* Alarm Record - '''Set'''
::4)* Alarm Snapshot - '''Set'''
::5)* Alarm OSD - '''DEFAULT(BACKING) ?'''
::6)* Alarm Buzzer - '''DEFAULT(On) ?'''
::7)* Switch View - '''DEFAULT(2) ?'''
::8)* Switch View Delay(Seconds) - '''0'''
::9)* Pre-record Time(Seconds) - '''20'''
::10)* Post-record Time(Seconds) - '''15'''

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Date_Time.png|left|400px|]]

::'''DST Settings'''

::1)* Date Format- '''mm-dd-yyyy'''
::2)* DVR Time - '''DEFAULT'''
::3)* Set Time - '''DEFAULT(Input current date and time)'''
::4)* Time Zone - '''(GMT-05:00) Eastern Time.'''
::5)* Time Offset - '''0'''
::6)* DST Period - '''Yes'''
::7)* DST Setting - '''USA'''
::8)* From - '''DEFAULT(User Input)'''
::9)* To - '''DEFAULT(User Input)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_Output_Setting.png|left|400px|]]

::'''Output Setting'''

::1)* Output Device - '''CVBS PAL ?'''
::2)* CVBS Output Volume(0-255) - '''16 ?'''
::3)* CVBS Output Reduction Value - '''0'''
::4)* ScreenSaver Delay(Seconds) - '''0'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_Setting_PTZ_Setting.png|left|400px|]]

 

::'''PTZ Settings'''

Apply the following to all four channels.

::1)* CH:01 - '''Baudrate 9600'''
::2)* CH:02 - '''Protocol PELCO-D'''
::3)* CH:03 - '''Address 0'''
::4)* CH:04 - '''DEFAULT'''

 

 ''' Copy to, apply, Return Buttons''' not shown in AMCAP

 

==File==

[[File:D4M_File.png|left|400px|]]

::'''File'''

No Setup needed.

 

==System==

[[File:D4M_System_Info.png|left|400px|]]

::'''System Info'''

::1)* DVR App Version - '''V206-2019/4/12-10:11::12-4'''
::2)* DVR MCU Version - '''08/04/2018-0d'''
::3)* Camera1 Version - '''NTSC)'''

 

 ''' Apply, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Upgrade.png|left|400px|]]

 

::'''System Upgrade'''

::1)* Current Version - '''V206-2019/4/12-10:11::12-4'''
::Confirm Current Version is the latest version; if not, browse available resources for upgrade?
::2)* Upgrade file - '''DEFAULT(Browse)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Config_Operation.png|left|400px|]]

::'''Config Operation'''

::1)* DEFAULT - '''DEFAULT'''
::2)* Import Configuration - '''DEFAULT ?)'''
::3)* Export Configuration - '''DEFAULT'''
::4)* Restart System - '''DEFAULT(Use only if changes were made)'''

 

 ''' Upgrade, Return Buttons''' not shown in AMCAP

[[File:D4M_System_Log.png|left|400px|]]

 

::'''System Log'''

::1)* DISPLAYS LOG - '''DEFAULT(Refresh only if necessary)'''

 

 ''' Refresh, Return Buttons''' not shown in AMCAP

File:D4M Back Panel.png

2019-04-30T16:20:35Z

Brian: